1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
|
/* Generic NS8390 register definitions. */
/* This file is part of Donald Becker's 8390 drivers, and is distributed
under the same license.
Some of these names and comments originated from the Crynwr
packet drivers, which are distributed under the GPL. */
#ifndef _8390_h
#define _8390_h
#include <linux/if_ether.h>
#include <linux/ioport.h>
#include <linux/skbuff.h>
#define TX_2X_PAGES 12
#define TX_1X_PAGES 6
/* Should always use two Tx slots to get back-to-back transmits. */
#define EI_PINGPONG
#ifdef EI_PINGPONG
#define TX_PAGES TX_2X_PAGES
#else
#define TX_PAGES TX_1X_PAGES
#endif
#define ETHER_ADDR_LEN 6
/* The 8390 specific per-packet-header format. */
struct e8390_pkt_hdr {
unsigned char status; /* status */
unsigned char next; /* pointer to next packet. */
unsigned short count; /* header + packet length in bytes */
};
/* From 8390.c */
extern int ei_debug;
extern struct sigaction ei_sigaction;
extern int ethif_init(struct device *dev);
extern int ethdev_init(struct device *dev);
extern void NS8390_init(struct device *dev, int startp);
extern int ei_open(struct device *dev);
extern int ei_close(struct device *dev);
extern void ei_interrupt(int irq, void *dev_id, struct pt_regs *regs);
#ifndef HAVE_AUTOIRQ
/* From auto_irq.c */
extern struct device *irq2dev_map[16];
extern int autoirq_setup(int waittime);
extern int autoirq_report(int waittime);
#endif
/* Most of these entries should be in 'struct device' (or most of the
things in there should be here!) */
/* You have one of these per-board */
struct ei_device {
const char *name;
void (*reset_8390)(struct device *);
void (*get_8390_hdr)(struct device *, struct e8390_pkt_hdr *, int);
void (*block_output)(struct device *, int, const unsigned char *, int);
void (*block_input)(struct device *, int, struct sk_buff *, int);
unsigned open:1;
unsigned word16:1; /* We have the 16-bit (vs 8-bit) version of the card. */
unsigned txing:1; /* Transmit Active */
unsigned irqlock:1; /* 8390's intrs disabled when '1'. */
unsigned dmaing:1; /* Remote DMA Active */
unsigned char tx_start_page, rx_start_page, stop_page;
unsigned char current_page; /* Read pointer in buffer */
unsigned char interface_num; /* Net port (AUI, 10bT.) to use. */
unsigned char txqueue; /* Tx Packet buffer queue length. */
short tx1, tx2; /* Packet lengths for ping-pong tx. */
short lasttx; /* Alpha version consistency check. */
unsigned char reg0; /* Register '0' in a WD8013 */
unsigned char reg5; /* Register '5' in a WD8013 */
unsigned char saved_irq; /* Original dev->irq value. */
/* The new statistics table. */
struct enet_statistics stat;
};
/* The maximum number of 8390 interrupt service routines called per IRQ. */
#define MAX_SERVICE 12
/* The maximum time waited (in jiffies) before assuming a Tx failed. (20ms) */
#define TX_TIMEOUT (20*HZ/100)
#define ei_status (*(struct ei_device *)(dev->priv))
/* Some generic ethernet register configurations. */
#define E8390_TX_IRQ_MASK 0xa /* For register EN0_ISR */
#define E8390_RX_IRQ_MASK 0x5
#define E8390_RXCONFIG 0x4 /* EN0_RXCR: broadcasts, no multicast,errors */
#define E8390_RXOFF 0x20 /* EN0_RXCR: Accept no packets */
#define E8390_TXCONFIG 0x00 /* EN0_TXCR: Normal transmit mode */
#define E8390_TXOFF 0x02 /* EN0_TXCR: Transmitter off */
/* Register accessed at EN_CMD, the 8390 base addr. */
#define E8390_STOP 0x01 /* Stop and reset the chip */
#define E8390_START 0x02 /* Start the chip, clear reset */
#define E8390_TRANS 0x04 /* Transmit a frame */
#define E8390_RREAD 0x08 /* Remote read */
#define E8390_RWRITE 0x10 /* Remote write */
#define E8390_NODMA 0x20 /* Remote DMA */
#define E8390_PAGE0 0x00 /* Select page chip registers */
#define E8390_PAGE1 0x40 /* using the two high-order bits */
#define E8390_PAGE2 0x80 /* Page 3 is invalid. */
#define E8390_CMD 0x00 /* The command register (for all pages) */
/* Page 0 register offsets. */
#define EN0_CLDALO 0x01 /* Low byte of current local dma addr RD */
#define EN0_STARTPG 0x01 /* Starting page of ring bfr WR */
#define EN0_CLDAHI 0x02 /* High byte of current local dma addr RD */
#define EN0_STOPPG 0x02 /* Ending page +1 of ring bfr WR */
#define EN0_BOUNDARY 0x03 /* Boundary page of ring bfr RD WR */
#define EN0_TSR 0x04 /* Transmit status reg RD */
#define EN0_TPSR 0x04 /* Transmit starting page WR */
#define EN0_NCR 0x05 /* Number of collision reg RD */
#define EN0_TCNTLO 0x05 /* Low byte of tx byte count WR */
#define EN0_FIFO 0x06 /* FIFO RD */
#define EN0_TCNTHI 0x06 /* High byte of tx byte count WR */
#define EN0_ISR 0x07 /* Interrupt status reg RD WR */
#define EN0_CRDALO 0x08 /* low byte of current remote dma address RD */
#define EN0_RSARLO 0x08 /* Remote start address reg 0 */
#define EN0_CRDAHI 0x09 /* high byte, current remote dma address RD */
#define EN0_RSARHI 0x09 /* Remote start address reg 1 */
#define EN0_RCNTLO 0x0a /* Remote byte count reg WR */
#define EN0_RCNTHI 0x0b /* Remote byte count reg WR */
#define EN0_RSR 0x0c /* rx status reg RD */
#define EN0_RXCR 0x0c /* RX configuration reg WR */
#define EN0_TXCR 0x0d /* TX configuration reg WR */
#define EN0_COUNTER0 0x0d /* Rcv alignment error counter RD */
#define EN0_DCFG 0x0e /* Data configuration reg WR */
#define EN0_COUNTER1 0x0e /* Rcv CRC error counter RD */
#define EN0_IMR 0x0f /* Interrupt mask reg WR */
#define EN0_COUNTER2 0x0f /* Rcv missed frame error counter RD */
/* Bits in EN0_ISR - Interrupt status register */
#define ENISR_RX 0x01 /* Receiver, no error */
#define ENISR_TX 0x02 /* Transmitter, no error */
#define ENISR_RX_ERR 0x04 /* Receiver, with error */
#define ENISR_TX_ERR 0x08 /* Transmitter, with error */
#define ENISR_OVER 0x10 /* Receiver overwrote the ring */
#define ENISR_COUNTERS 0x20 /* Counters need emptying */
#define ENISR_RDC 0x40 /* remote dma complete */
#define ENISR_RESET 0x80 /* Reset completed */
#define ENISR_ALL 0x3f /* Interrupts we will enable */
/* Bits in EN0_DCFG - Data config register */
#define ENDCFG_WTS 0x01 /* word transfer mode selection */
/* Page 1 register offsets. */
#define EN1_PHYS 0x01 /* This board's physical enet addr RD WR */
#define EN1_CURPAG 0x07 /* Current memory page RD WR */
#define EN1_MULT 0x08 /* Multicast filter mask array (8 bytes) RD WR */
/* Bits in received packet status byte and EN0_RSR*/
#define ENRSR_RXOK 0x01 /* Received a good packet */
#define ENRSR_CRC 0x02 /* CRC error */
#define ENRSR_FAE 0x04 /* frame alignment error */
#define ENRSR_FO 0x08 /* FIFO overrun */
#define ENRSR_MPA 0x10 /* missed pkt */
#define ENRSR_PHY 0x20 /* physical/multicase address */
#define ENRSR_DIS 0x40 /* receiver disable. set in monitor mode */
#define ENRSR_DEF 0x80 /* deferring */
/* Transmitted packet status, EN0_TSR. */
#define ENTSR_PTX 0x01 /* Packet transmitted without error */
#define ENTSR_ND 0x02 /* The transmit wasn't deferred. */
#define ENTSR_COL 0x04 /* The transmit collided at least once. */
#define ENTSR_ABT 0x08 /* The transmit collided 16 times, and was deferred. */
#define ENTSR_CRS 0x10 /* The carrier sense was lost. */
#define ENTSR_FU 0x20 /* A "FIFO underrun" occurred during transmit. */
#define ENTSR_CDH 0x40 /* The collision detect "heartbeat" signal was lost. */
#define ENTSR_OWC 0x80 /* There was an out-of-window collision. */
#endif /* _8390_h */
|
