New upstream snapshot

- patches/10_cdromlock.patch: Remove, merged upstream
- patches/13_ide_dma.patch: Remove, merged upstream
- patches/24_pci_irq_fix.patch: Remove, merged upstream

5 files changed, 5 insertions, 1215 deletions

diff --git a/debian/changelog b/debian/changelog
index f8f8d73..818e092 100644
--- a/debian/changelog
+++ b/debian/changelog
@@ -1,5 +1,9 @@
-gnumach (2:1.3.99.dfsg.git20120710-2) UNRELEASED; urgency=low
+gnumach (2:1.3.99.dfsg.git20120923-1) UNRELEASED; urgency=low
 
+  * New upstream snapshot
+    - patches/10_cdromlock.patch: Remove, merged upstream
+    - patches/13_ide_dma.patch: Remove, merged upstream
+    - patches/24_pci_irq_fix.patch: Remove, merged upstream
   * patches/60_bigmem.patch: Also set Xen to 2/2 memory model.
   * patches/40_iopl_mem.patch: Remove
   * control: Break xserver before 1.9.99.1.
diff --git a/debian/patches/10_cdromlock.patch b/debian/patches/10_cdromlock.patch
deleted file mode 100644
index 436f97c..0000000
--- a/debian/patches/10_cdromlock.patch
+++ /dev/null
@@ -1,93 +0,0 @@
-Index: b/linux/dev/glue/block.c
-===================================================================
---- a/linux/dev/glue/block.c
-+++ b/linux/dev/glue/block.c
-@@ -789,6 +789,7 @@ static struct block_data *open_list;
- extern struct device_emulation_ops linux_block_emulation_ops;
- 
- static io_return_t device_close (void *);
-+static io_return_t device_close_forced (void *, int);
- 
- /* Return a send right for block device BD.  */
- static ipc_port_t
-@@ -1164,6 +1165,7 @@ out:
- 	    {
- 	      ipc_kobject_set (bd->port, IKO_NULL, IKOT_NONE);
- 	      ipc_port_dealloc_kernel (bd->port);
-+            *devp = IP_NULL;
- 	    }
- 	  kfree ((vm_offset_t) bd, sizeof (struct block_data));
- 	  bd = NULL;
-@@ -1174,18 +1176,16 @@ out:
-       bd->open_count = 1;
-       bd->next = open_list;
-       open_list = bd;
-+      *devp = &bd -> device;
-     }
- 
--  if (IP_VALID (reply_port))
--    ds_device_open_reply (reply_port, reply_port_type, err, dev_to_port (bd));
--  else if (! err)
-+  if (!IP_VALID (reply_port) && ! err)
-     device_close (bd);
--
--  return MIG_NO_REPLY;
-+  return err;
- }
- 
- static io_return_t
--device_close (void *d)
-+device_close_forced (void *d, int force)
- {
-   struct block_data *bd = d, *bdp, **prev;
-   struct device_struct *ds = bd->ds;
-@@ -1202,7 +1202,7 @@ device_close (void *d)
-     }
-   ds->busy = 1;
- 
--  if (--bd->open_count == 0)
-+  if (force || --bd->open_count == 0)
-     {
-       /* Wait for pending I/O to complete.  */
-       while (bd->iocount > 0)
-@@ -1245,6 +1245,13 @@ device_close (void *d)
-   return D_SUCCESS;
- }
- 
-+static io_return_t
-+device_close (void *d)
-+{
-+  return device_close_forced (d, 0);
-+}
-+
-+
- #define MAX_COPY	(VM_MAP_COPY_PAGE_LIST_MAX << PAGE_SHIFT)
- 
- /* Check block BN and size COUNT for I/O validity
-@@ -1704,6 +1711,17 @@ device_get_status (void *d, dev_flavor_t
-   return D_INVALID_OPERATION;
- }
- 
-+
-+static void
-+device_no_senders (mach_no_senders_notification_t *ns)
-+{
-+  device_t dev;
-+
-+  dev = dev_port_lookup((ipc_port_t) ns->not_header.msgh_remote_port);
-+  assert(dev);
-+  device_close_forced (dev->emul_data, 1);
-+}
-+
- struct device_emulation_ops linux_block_emulation_ops =
- {
-   NULL,
-@@ -1719,7 +1737,7 @@ struct device_emulation_ops linux_block_
-   device_get_status,
-   NULL,
-   NULL,
--  NULL,
-+  device_no_senders,
-   NULL,
-   NULL
- };
diff --git a/debian/patches/13_ide_dma.patch b/debian/patches/13_ide_dma.patch
deleted file mode 100644
index 2a950fa..0000000
--- a/debian/patches/13_ide_dma.patch
+++ /dev/null
@@ -1,1085 +0,0 @@
-Do not --enable-ide-forcedma by default, it's too dangerous on non-DMA
-supporting hardware.
-
-2004-09-17  Sergio Lopez  <koro@sinrega.org>
-
-
-Index: b/linux/src/drivers/block/ide.c
-===================================================================
---- a/linux/src/drivers/block/ide.c
-+++ b/linux/src/drivers/block/ide.c
-@@ -3594,9 +3594,6 @@ static void ide_probe_promise_20246(void
- 		hwif->ctl_port = io[tmp + 1] + 2;
- 		hwif->noprobe = 0;
- 	}
--#ifdef CONFIG_BLK_DEV_TRITON
--	ide_init_promise (bus, fn, &ide_hwifs[2], &ide_hwifs[3], io[4]);
--#endif /* CONFIG_BLK_DEV_TRITON */
- }
- 
- #endif /* CONFIG_PCI */
-@@ -3629,6 +3626,9 @@ static void probe_for_hwifs (void)
- 		ide_probe_pci (PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371_0, &ide_init_triton, 1);
- 		ide_probe_pci (PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, &ide_init_triton, 0);
- 		ide_probe_pci (PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, &ide_init_triton, 0);
-+		ide_probe_pci (PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5513, &ide_init_triton, 0);
-+		ide_probe_pci (PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, &ide_init_triton, 0);
-+		ide_probe_pci (PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M5229, &ide_init_triton, 0);
- #endif /* CONFIG_BLK_DEV_TRITON */
- 		ide_probe_promise_20246();
- 	}
-@@ -3703,8 +3703,9 @@ int ide_init (void)
- 
- 	init_ide_data ();
- 	/*
--	 * Probe for special "known" interface chipsets
-+	 * Probe for special "known" interface chipsets.
- 	 */
-+	 
- 	probe_for_hwifs ();
- 
- 	/*
-Index: b/linux/src/drivers/block/ide.h
-===================================================================
---- a/linux/src/drivers/block/ide.h
-+++ b/linux/src/drivers/block/ide.h
-@@ -429,7 +429,8 @@ typedef void (ide_selectproc_t) (ide_dri
- typedef enum {	ide_unknown,	ide_generic,	ide_triton,
- 		ide_cmd640,	ide_dtc2278,	ide_ali14xx,
- 		ide_qd6580,	ide_umc8672,	ide_ht6560b,
--		ide_promise,	ide_promise_udma }
-+		ide_promise,	ide_hpt343,	ide_udma,
-+		ide_ultra66 }
- 	hwif_chipset_t;
- 
- typedef struct hwif_s {
-Index: b/linux/src/drivers/block/triton.c
-===================================================================
---- a/linux/src/drivers/block/triton.c
-+++ b/linux/src/drivers/block/triton.c
-@@ -1,107 +1,20 @@
- /*
-  *  linux/drivers/block/triton.c	Version 1.13  Aug 12, 1996
-+ *					Version 1.13a June 1998 - new chipsets
-+ *					Version 1.13b July 1998 - DMA blacklist
-+ *					Version 1.14  June 22, 1999
-  *
-+ *  Copyright (c) 1998-1999  Andre Hedrick
-  *  Copyright (c) 1995-1996  Mark Lord
-  *  May be copied or modified under the terms of the GNU General Public License
-  */
- 
- /*
-- * This module provides support for the Bus Master IDE DMA function
-- * of the Intel PCI Triton I/II chipsets (i82371FB or i82371SB).
-- *
-- * Pretty much the same code will work for the OPTi "Viper" chipset.
-- * Look for DMA support for this in linux kernel 2.1.xx, when it appears.
-- *
-- * DMA is currently supported only for hard disk drives (not cdroms).
-- *
-- * Support for cdroms will likely be added at a later date,
-- * after broader experience has been obtained with hard disks.
-- *
-- * Up to four drives may be enabled for DMA, and the Triton chipset will
-- * (hopefully) arbitrate the PCI bus among them.  Note that the i82371 chip
-- * provides a single "line buffer" for the BM IDE function, so performance of
-- * multiple (two) drives doing DMA simultaneously will suffer somewhat,
-- * as they contest for that resource bottleneck.  This is handled transparently
-- * inside the i82371 chip.
-- *
-- * By default, DMA support is prepared for use, but is currently enabled only
-- * for drives which support multi-word DMA mode2 (mword2), or which are
-- * recognized as "good" (see table below).  Drives with only mode0 or mode1
-- * (single or multi) DMA should also work with this chipset/driver (eg. MC2112A)
-- * but are not enabled by default.  Use "hdparm -i" to view modes supported
-- * by a given drive.
-- *
-- * The hdparm-2.4 (or later) utility can be used for manually enabling/disabling
-- * DMA support, but must be (re-)compiled against this kernel version or later.
-- *
-- * To enable DMA, use "hdparm -d1 /dev/hd?" on a per-drive basis after booting.
-- * If problems arise, ide.c will disable DMA operation after a few retries.
-- * This error recovery mechanism works and has been extremely well exercised.
-- *
-- * IDE drives, depending on their vintage, may support several different modes
-- * of DMA operation.  The boot-time modes are indicated with a "*" in
-- * the "hdparm -i" listing, and can be changed with *knowledgeable* use of
-- * the "hdparm -X" feature.  There is seldom a need to do this, as drives
-- * normally power-up with their "best" PIO/DMA modes enabled.
-- *
-- * Testing was done with an ASUS P55TP4XE/100 system and the following drives:
-- *
-- *   Quantum Fireball 1080A (1Gig w/83kB buffer), DMA mode2, PIO mode4.
-- *	- DMA mode2 works well (7.4MB/sec), despite the tiny on-drive buffer.
-- *	- This drive also does PIO mode4, at about the same speed as DMA mode2.
-- *	  An awesome drive for the price!
-- *
-- *   Fujitsu M1606TA (1Gig w/256kB buffer), DMA mode2, PIO mode4.
-- *	- DMA mode2 gives horrible performance (1.6MB/sec), despite the good
-- *	  size of the on-drive buffer and a boasted 10ms average access time.
-- *	- PIO mode4 was better, but peaked at a mere 4.5MB/sec.
-- *
-- *   Micropolis MC2112A (1Gig w/508kB buffer), drive pre-dates EIDE and ATA2.
-- *	- DMA works fine (2.2MB/sec), probably due to the large on-drive buffer.
-- *	- This older drive can also be tweaked for fastPIO (3.7MB/sec) by using
-- *	  maximum clock settings (5,4) and setting all flags except prefetch.
-- *
-- *   Western Digital AC31000H (1Gig w/128kB buffer), DMA mode1, PIO mode3.
-- *	- DMA does not work reliably.  The drive appears to be somewhat tardy
-- *	  in deasserting DMARQ at the end of a sector.  This is evident in
-- *	  the observation that WRITEs work most of the time, depending on
-- *	  cache-buffer occupancy, but multi-sector reads seldom work.
-- *
-- * Testing was done with a Gigabyte GA-586 ATE system and the following drive:
-- * (Uwe Bonnes - bon@elektron.ikp.physik.th-darmstadt.de)
-- *
-- *   Western Digital AC31600H (1.6Gig w/128kB buffer), DMA mode2, PIO mode4.
-- *	- much better than its 1Gig cousin, this drive is reported to work
-- *	  very well with DMA (7.3MB/sec).
-- *
-- * Other drives:
-- *
-- *   Maxtor 7540AV (515Meg w/32kB buffer), DMA modes mword0/sword2, PIO mode3.
-- *	- a budget drive, with budget performance, around 3MB/sec.
-- *
-- *   Western Digital AC2850F (814Meg w/64kB buffer), DMA mode1, PIO mode3.
-- *	- another "caviar" drive, similar to the AC31000, except that this one
-- *	  worked with DMA in at least one system.  Throughput is about 3.8MB/sec
-- *	  for both DMA and PIO.
-- *
-- *   Conner CFS850A (812Meg w/64kB buffer), DMA mode2, PIO mode4.
-- *	- like most Conner models, this drive proves that even a fast interface
-- *	  cannot improve slow media.  Both DMA and PIO peak around 3.5MB/sec.
-- *
-- *   Maxtor 71260AT (1204Meg w/256kB buffer), DMA mword0/sword2, PIO mode3.
-- *	- works with DMA, on some systems (but not always on others, eg. Dell),
-- *	giving 3-4MB/sec performance, about the same as mode3.
-- *
-- * If you have any drive models to add, email your results to:  mlord@pobox.com
-- * Keep an eye on /var/adm/messages for "DMA disabled" messages.
-- *
-- * Some people have reported trouble with Intel Zappa motherboards.
-- * This can be fixed by upgrading the AMI BIOS to version 1.00.04.BS0,
-- * available from ftp://ftp.intel.com/pub/bios/10004bs0.exe
-- * (thanks to Glen Morrell <glen@spin.Stanford.edu> for researching this).
-- *
-- * And, yes, Intel Zappa boards really *do* use the Triton IDE ports.
-+ * This module provides support for Bus Master IDE DMA functions in various
-+ * motherboard chipsets and PCI controller cards.
-+ * Please check /Documentation/ide.txt and /Documentation/udma.txt for details.
-  */
-+
- #include <linux/config.h>
- #include <linux/types.h>
- #include <linux/kernel.h>
-@@ -116,10 +29,24 @@
- 
- #include <asm/io.h>
- #include <asm/dma.h>
-+#include <asm/irq.h>
- 
- #include "ide.h"
- 
- #undef DISPLAY_TRITON_TIMINGS	/* define this to display timings */
-+#undef DISPLAY_APOLLO_TIMINGS	/* define this for extensive debugging information */
-+#undef DISPLAY_ALI15X3_TIMINGS	/* define this for extensive debugging information */
-+
-+#if defined(CONFIG_PROC_FS)
-+#include <linux/stat.h>
-+#include <linux/proc_fs.h>
-+#ifdef DISPLAY_APOLLO_TIMINGS
-+#include <linux/via_ide_dma.h>
-+#endif
-+#ifdef DISPLAY_ALI15X3_TIMINGS
-+#include <linux/ali_ide_dma.h>
-+#endif
-+#endif
- 
- /*
-  * good_dma_drives() lists the model names (from "hdparm -i")
-@@ -132,6 +59,27 @@ const char *good_dma_drives[] = {"Microp
- 				 NULL};
- 
- /*
-+ * bad_dma_drives() lists the model names (from "hdparm -i")
-+ * of drives which supposedly support (U)DMA but which are
-+ * known to corrupt data with this interface under Linux.
-+ *
-+ * Note: the list was generated by statistical analysis of problem
-+ * reports. It's not clear if there are problems with the drives,
-+ * or with some combination of drive/controller or what. 
-+ *
-+ * You can forcibly override this if you wish. This is the kernel
-+ * 'Tread carefully' list.
-+ *
-+ * Finally see http://www.wdc.com/quality/err-rec.html if you have
-+ * one of the listed drives. 
-+ */
-+const char *bad_dma_drives[] = {"WDC AC11000H",
-+				"WDC AC22100H",
-+				"WDC AC32500H",
-+				"WDC AC33100H",
-+				 NULL};
-+
-+/*
-  * Our Physical Region Descriptor (PRD) table should be large enough
-  * to handle the biggest I/O request we are likely to see.  Since requests
-  * can have no more than 256 sectors, and since the typical blocksize is
-@@ -150,6 +98,8 @@ const char *good_dma_drives[] = {"Microp
- #define PRD_BYTES	8
- #define PRD_ENTRIES	(PAGE_SIZE / (2 * PRD_BYTES))
- #define DEFAULT_BMIBA	0xe800	/* in case BIOS did not init it */
-+#define DEFAULT_BMCRBA  0xcc00  /* VIA's default value */
-+#define DEFAULT_BMALIBA	0xd400	/* ALI's default value */
- 
- /*
-  * dma_intr() is the handler for disk read/write DMA interrupts
-@@ -244,23 +194,57 @@ static int build_dmatable (ide_drive_t *
- 	return 1;	/* let the PIO routines handle this weirdness */
- }
- 
-+/*
-+ * We will only enable drives with multi-word (mode2) (U)DMA capabilities,
-+ * and ignore the very rare cases of drives that can only do single-word
-+ * (modes 0 & 1) (U)DMA transfers. We also discard "blacklisted" hard disks.
-+ */
- static int config_drive_for_dma (ide_drive_t *drive)
- {
-+#ifndef CONFIG_BLK_DEV_FORCE_DMA
- 	const char **list;
- 	struct hd_driveid *id = drive->id;
-+#endif
-+
-+#ifdef CONFIG_BLK_DEV_FORCE_DMA
-+	drive->using_dma = 1;
-+	return 0;
-+#else
-+	if (HWIF(drive)->chipset == ide_hpt343) {
-+		drive->using_dma = 0;	/* no DMA */
-+		return 1;	/* DMA disabled */
-+	}
- 
- 	if (id && (id->capability & 1)) {
--		/* Enable DMA on any drive that has UltraDMA (mode 0/1/2) enabled */
--		if (id->field_valid & 4)	/* UltraDMA */
--			if  ((id->dma_ultra & (id->dma_ultra >> 8) & 7)) {
-+		/* Consult the list of known "bad" drives */
-+		list = bad_dma_drives;
-+		while (*list) {
-+			if (!strcmp(*list++,id->model)) {
-+				drive->using_dma = 0;   /* no DMA */
-+				printk("ide: Disabling DMA modes on %s drive (%s).\n", drive->name, id->model);
-+				return 1;	/* DMA disabled */
-+			}
-+		}
-+		/* Enable DMA on any drive that has mode 4 or 2 UltraDMA enabled */
-+		if (id->field_valid & 4) {	/* UltraDMA */
-+			/* Enable DMA on any drive that has mode 4 UltraDMA enabled */
-+			if (((id->dma_ultra & 0x1010) == 0x1010) &&
-+			    (id->word93 & 0x2000) &&
-+			    (HWIF(drive)->chipset == ide_ultra66)) {
- 				drive->using_dma = 1;
--				return 0;	/* dma enabled */
-+				return 0;	/* DMA enabled */
-+			} else
-+			/* Enable DMA on any drive that has mode 2 UltraDMA enabled */
-+				if ((id->dma_ultra & 0x404) == 0x404) {
-+				drive->using_dma = 1;
-+				return 0;	/* DMA enabled */
- 			}
--		/* Enable DMA on any drive that has mode2 DMA (multi or single) enabled */
-+		}
-+		/* Enable DMA on any drive that has mode2 DMA enabled */
- 		if (id->field_valid & 2)	/* regular DMA */
--			if  ((id->dma_mword & 0x404) == 0x404 || (id->dma_1word & 0x404) == 0x404) {
-+			if ((id->dma_mword & 0x404) == 0x404) {
- 				drive->using_dma = 1;
--				return 0;	/* dma enabled */
-+				return 0;	/* DMA enabled */
- 			}
- 		/* Consult the list of known "good" drives */
- 		list = good_dma_drives;
-@@ -272,6 +256,7 @@ static int config_drive_for_dma (ide_dri
- 		}
- 	}
- 	return 1;	/* DMA not enabled */
-+#endif
- }
- 
- /*
-@@ -387,22 +372,260 @@ static void init_triton_dma (ide_hwif_t 
- }
- 
- /*
-+ *  Set VIA Chipset Timings for (U)DMA modes enabled.
-+ */
-+static int set_via_timings (byte bus, byte fn, byte post, byte flush)
-+{
-+	byte via_config = 0;
-+	int rc = 0;
-+
-+	/* setting IDE read prefetch buffer and IDE post write buffer */
-+	if ((rc = pcibios_read_config_byte(bus, fn, 0x41, &via_config)))
-+		return (1);
-+	if ((rc = pcibios_write_config_byte(bus, fn, 0x41, via_config | post)))
-+		return (1);
-+
-+	/* setting Channel read and End-of-sector FIFO flush: */
-+	if ((rc = pcibios_read_config_byte(bus, fn, 0x46, &via_config)))
-+		return (1);
-+	if ((rc = pcibios_write_config_byte(bus, fn, 0x46, via_config | flush)))
-+		return (1);
-+
-+	return (0);
-+}
-+
-+static int setup_aladdin (byte bus, byte fn)
-+{
-+	byte confreg0 = 0, confreg1 = 0, progif = 0;
-+	int errors = 0;
-+
-+	if (pcibios_read_config_byte(bus, fn, 0x50, &confreg1))
-+		goto veryspecialsettingserror;
-+	if (!(confreg1 & 0x02))
-+		if (pcibios_write_config_byte(bus, fn, 0x50, confreg1 | 0x02))
-+			goto veryspecialsettingserror;
-+
-+	if (pcibios_read_config_byte(bus, fn, 0x09, &progif))
-+		goto veryspecialsettingserror;
-+	if (!(progif & 0x40)) {
-+		/*
-+		 * The way to enable them is to set progif
-+		 * writable at 0x4Dh register, and set bit 6
-+		 * of progif to 1:
-+		 */
-+		if (pcibios_read_config_byte(bus, fn, 0x4d, &confreg0))
-+			goto veryspecialsettingserror;
-+		if (confreg0 & 0x80)
-+			if (pcibios_write_config_byte(bus, fn, 0x4d, confreg0 & ~0x80))
-+				goto veryspecialsettingserror;
-+		if (pcibios_write_config_byte(bus, fn, 0x09, progif | 0x40))
-+			goto veryspecialsettingserror;
-+		if (confreg0 & 0x80)
-+			if (pcibios_write_config_byte(bus, fn, 0x4d, confreg0))
-+				errors++;
-+	}
-+
-+	if ((pcibios_read_config_byte(bus, fn, 0x09, &progif)) || (!(progif & 0x40)))
-+		goto veryspecialsettingserror;
-+
-+	printk("ide: ALI15X3: enabled read of IDE channels state (en/dis-abled) %s.\n",
-+		errors ? "with Error(s)" : "Succeeded" );
-+	return 1;
-+veryspecialsettingserror:
-+	printk("ide: ALI15X3: impossible to enable read of IDE channels state (en/dis-abled)!\n");
-+	return 0;
-+}
-+
-+void set_promise_hpt343_extra (unsigned short device, unsigned int bmiba)
-+{
-+	switch(device) {
-+		case PCI_DEVICE_ID_PROMISE_20246:
-+			if(!check_region((bmiba+16), 16))
-+				request_region((bmiba+16), 16, "PDC20246");
-+			break;
-+		case PCI_DEVICE_ID_PROMISE_20262:
-+			if (!check_region((bmiba+48), 48))
-+				request_region((bmiba+48), 48, "PDC20262");
-+			break;
-+		case PCI_DEVICE_ID_TTI_HPT343:
-+			if(!check_region((bmiba+16), 16))
-+				request_region((bmiba+16), 16, "HPT343");
-+			break;
-+		default:
-+			break;
-+	}
-+}
-+
-+#define HPT343_PCI_INIT_REG		0x80
-+
-+/*
-  * ide_init_triton() prepares the IDE driver for DMA operation.
-  * This routine is called once, from ide.c during driver initialization,
-- * for each triton chipset which is found (unlikely to be more than one).
-+ * for each BM-DMA chipset which is found (rarely more than one).
-  */
- void ide_init_triton (byte bus, byte fn)
- {
--	int rc = 0, h;
--	int dma_enabled = 0;
--	unsigned short pcicmd;
--	unsigned int bmiba, timings;
-+	byte bridgebus, bridgefn, bridgeset = 0, hpt34x_flag = 0;
-+	unsigned char irq = 0;
-+	int dma_enabled = 0, rc = 0, h;
-+	unsigned short io[6], count = 0, step_count = 0, pass_count = 0;
-+	unsigned short pcicmd, vendor, device, class;
-+	unsigned int bmiba, timings, reg, tmp;
-+	unsigned int addressbios = 0;
-+	unsigned long flags;
-+	unsigned index;
-+
-+#if defined(DISPLAY_APOLLO_TIMINGS) || defined(DISPLAY_ALI15X3_TIMINGS)
-+	bmide_bus = bus;
-+	bmide_fn = fn;
-+#endif /* DISPLAY_APOLLO_TIMINGS || DISPLAY_ALI15X3_TIMINGS */
-+
-+/*
-+ *  We pick up the vendor, device, and class info for selecting the correct
-+ *  controller that is supported.  Since we can access this routine more than
-+ *  once with the use of onboard and off-board EIDE controllers, a method
-+ *  of determining "who is who for what" is needed.
-+ */
-+
-+	pcibios_read_config_word (bus, fn, PCI_VENDOR_ID, &vendor);
-+	pcibios_read_config_word (bus, fn, PCI_DEVICE_ID, &device);
-+	pcibios_read_config_word (bus, fn, PCI_CLASS_DEVICE, &class);
-+	pcibios_read_config_byte (bus, fn, PCI_INTERRUPT_LINE, &irq);
-+
-+	switch(vendor) {
-+		case PCI_VENDOR_ID_INTEL:
-+			printk("ide: Intel 82371 ");
-+			switch(device) {
-+				case PCI_DEVICE_ID_INTEL_82371_0:
-+					printk("PIIX (single FIFO) ");
-+					break;
-+				case PCI_DEVICE_ID_INTEL_82371SB_1:
-+					printk("PIIX3 (dual FIFO) ");
-+					break;
-+				case PCI_DEVICE_ID_INTEL_82371AB:
-+					printk("PIIX4 (dual FIFO) ");
-+					break;
-+				default:
-+					printk(" (unknown) 0x%04x ", device);
-+					break;
-+			}
-+			printk("DMA Bus Mastering IDE ");
-+			break;
-+		case PCI_VENDOR_ID_SI:
-+			printk("ide: SiS 5513 (dual FIFO) DMA Bus Mastering IDE ");
-+			break;
-+                case PCI_VENDOR_ID_VIA:
-+			printk("ide: VIA VT82C586B (split FIFO) UDMA Bus Mastering IDE ");
-+			break;
-+		case PCI_VENDOR_ID_TTI:
-+			/*PCI_CLASS_STORAGE_UNKNOWN == class */
-+			if (device == PCI_DEVICE_ID_TTI_HPT343) {
-+				pcibios_write_config_byte(bus, fn, HPT343_PCI_INIT_REG, 0x00);
-+				pcibios_read_config_word(bus, fn, PCI_COMMAND, &pcicmd);
-+				hpt34x_flag = (pcicmd & PCI_COMMAND_MEMORY) ? 1 : 0;
-+#if 1
-+				if (!hpt34x_flag) {
-+					save_flags(flags);
-+					cli();
-+					pcibios_write_config_word(bus, fn, PCI_COMMAND, pcicmd & ~PCI_COMMAND_IO);
-+					pcibios_read_config_dword(bus, fn, PCI_BASE_ADDRESS_4, &bmiba);
-+					pcibios_write_config_dword(bus, fn, PCI_BASE_ADDRESS_0, bmiba | 0x20);
-+					pcibios_write_config_dword(bus, fn, PCI_BASE_ADDRESS_1, bmiba | 0x34);
-+					pcibios_write_config_dword(bus, fn, PCI_BASE_ADDRESS_2, bmiba | 0x28);
-+					pcibios_write_config_dword(bus, fn, PCI_BASE_ADDRESS_3, bmiba | 0x3c);
-+					pcibios_write_config_word(bus, fn, PCI_COMMAND, pcicmd);
-+					bmiba = 0;
-+					restore_flags(flags);
-+				}
-+#endif
-+				pcibios_write_config_byte(bus, fn, PCI_LATENCY_TIMER, 0x20); 
-+				goto hpt343_jump_in;
-+			} else {
-+				printk("ide: HPTXXX did == 0x%04X unsupport chipset error.\n", device);
-+				return;
-+			}
-+		case PCI_VENDOR_ID_PROMISE:
-+			/*
-+			 *  I have been able to make my Promise Ultra33 UDMA card change class.
-+			 *  It has reported as both PCI_CLASS_STORAGE_RAID and PCI_CLASS_STORAGE_IDE.
-+			 *  Since the PCI_CLASS_STORAGE_RAID mode should automatically mirror the
-+			 *  two halves of the PCI_CONFIG register data, but sometimes it forgets.
-+			 *  Thus we guarantee that they are identical, with a quick check and
-+			 *  correction if needed.
-+			 *  PDC20246 (primary) PDC20247 (secondary) IDE hwif's.
-+			 *
-+			 *  PDC20262 Promise Ultra66 UDMA.
-+			 *
-+			 *  Note that Promise "stories,fibs,..." about this device not being
-+			 *  capable of ATAPI and AT devices.
-+			 */
-+			if (class != PCI_CLASS_STORAGE_IDE) {
-+				unsigned char irq_mirror = 0;
-+
-+				pcibios_read_config_byte(bus, fn, (PCI_INTERRUPT_LINE)|0x80, &irq_mirror);
-+				if (irq != irq_mirror) {
-+					pcibios_write_config_byte(bus, fn, (PCI_INTERRUPT_LINE)|0x80, irq);
-+				}
-+			}
-+		case PCI_VENDOR_ID_ARTOP:
-+			/*	PCI_CLASS_STORAGE_SCSI == class	*/
-+			/*
-+			 *  I have found that by stroking rom_enable_bit on both the AEC6210U/UF and
-+			 *  PDC20246 controller cards, the features desired are almost guaranteed
-+			 *  to be enabled and compatible.  This ROM may not be registered in the
-+			 *  config data, but it can be turned on.  Registration failure has only
-+			 *  been observed if and only if Linux sets up the pci_io_address in the
-+			 *  0x6000 range.  If they are setup in the 0xef00 range it is reported.
-+			 *  WHY??? got me.........
-+			 */
-+hpt343_jump_in:
-+			printk("ide: %s UDMA Bus Mastering ",
-+				(device == PCI_DEVICE_ID_ARTOP_ATP850UF) 		? "AEC6210" :
-+				(device == PCI_DEVICE_ID_PROMISE_20246)  		? "PDC20246" :
-+				(device == PCI_DEVICE_ID_PROMISE_20262)  		? "PDC20262" :
-+				(hpt34x_flag && (device == PCI_DEVICE_ID_TTI_HPT343))	? "HPT345" :
-+				(device == PCI_DEVICE_ID_TTI_HPT343)     		? "HPT343" : "UNKNOWN");
-+			pcibios_read_config_dword(bus, fn, PCI_ROM_ADDRESS, &addressbios);
-+			if (addressbios) {
-+				pcibios_write_config_byte(bus, fn, PCI_ROM_ADDRESS, addressbios | PCI_ROM_ADDRESS_ENABLE);
-+				printk("with ROM enabled at 0x%08x", addressbios);
-+			}
-+			/*
-+			 *  This was stripped out of 2.1.XXX kernel code and parts from a patch called
-+			 *  promise_update.  This finds the PCI_BASE_ADDRESS spaces and makes them
-+			 *  available for configuration later.
-+			 *  PCI_BASE_ADDRESS_0  hwif0->io_base
-+			 *  PCI_BASE_ADDRESS_1  hwif0->ctl_port
-+			 *  PCI_BASE_ADDRESS_2  hwif1->io_base
-+			 *  PCI_BASE_ADDRESS_3  hwif1->ctl_port
-+			 *  PCI_BASE_ADDRESS_4  bmiba
-+			 */
-+			memset(io, 0, 6 * sizeof(unsigned short));
-+			for (reg = PCI_BASE_ADDRESS_0; reg <= PCI_BASE_ADDRESS_5; reg += 4) {
-+				pcibios_read_config_dword(bus, fn, reg, &tmp);
-+				if (tmp & PCI_BASE_ADDRESS_SPACE_IO)
-+					io[count++] = tmp & PCI_BASE_ADDRESS_IO_MASK;
-+			}
-+			break;
-+		case PCI_VENDOR_ID_AL:
-+			save_flags(flags);
-+			cli();
-+			for (index = 0; !pcibios_find_device (PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, index, &bridgebus, &bridgefn); ++index) {
-+				bridgeset = setup_aladdin(bus, fn);
-+			}
-+			restore_flags(flags);
-+			printk("ide: ALI15X3 (dual FIFO) DMA Bus Mastering IDE ");
-+			break;
-+		default:
-+			return;
-+	}
-+
-+	printk("\n    Controller on PCI bus %d function %d\n", bus, fn);
- 
--	printk("ide: i82371 PIIX (Triton) on PCI bus %d function %d\n", bus, fn);
- 	/*
- 	 * See if IDE and BM-DMA features are enabled:
- 	 */
--	if ((rc = pcibios_read_config_word(bus, fn, 0x04, &pcicmd)))
-+	if ((rc = pcibios_read_config_word(bus, fn, PCI_COMMAND, &pcicmd)))
- 		goto quit;
- 	if ((pcicmd & 1) == 0)  {
- 		printk("ide: ports are not enabled (BIOS)\n");
-@@ -426,21 +649,29 @@ void ide_init_triton (byte bus, byte fn)
- 		 */
- 		int try_again = 1;
- 		do {
--			if ((rc = pcibios_read_config_dword(bus, fn, 0x20, &bmiba)))
-+			if ((rc = pcibios_read_config_dword(bus, fn, PCI_BASE_ADDRESS_4, &bmiba)))
- 				goto quit;
- 			bmiba &= 0xfff0;	/* extract port base address */
- 			if (bmiba) {
- 				dma_enabled = 1;
- 				break;
- 			} else {
--				printk("ide: BM-DMA base register is invalid (0x%04x, PnP BIOS problem)\n", bmiba);
--				if (inb(DEFAULT_BMIBA) != 0xff || !try_again)
-+                                printk("ide: BM-DMA base register is invalid (0x%04x, PnP BIOS problem)\n", bmiba);
-+                                if (inb(((vendor == PCI_VENDOR_ID_AL) ? DEFAULT_BMALIBA :
-+					 (vendor == PCI_VENDOR_ID_VIA) ? DEFAULT_BMCRBA :
-+									DEFAULT_BMIBA)) != 0xff || !try_again)
- 					break;
--				printk("ide: setting BM-DMA base register to 0x%04x\n", DEFAULT_BMIBA);
--				if ((rc = pcibios_write_config_word(bus, fn, 0x04, pcicmd&~1)))
-+				printk("ide: setting BM-DMA base register to 0x%04x\n",
-+					((vendor == PCI_VENDOR_ID_AL) ? DEFAULT_BMALIBA :
-+					 (vendor == PCI_VENDOR_ID_VIA) ? DEFAULT_BMCRBA :
-+									DEFAULT_BMIBA));
-+				if ((rc = pcibios_write_config_word(bus, fn, PCI_COMMAND, pcicmd&~1)))
- 					goto quit;
--				rc = pcibios_write_config_dword(bus, fn, 0x20, DEFAULT_BMIBA|1);
--				if (pcibios_write_config_word(bus, fn, 0x04, pcicmd|5) || rc)
-+				rc = pcibios_write_config_dword(bus, fn, 0x20,
-+					((vendor == PCI_VENDOR_ID_AL) ? DEFAULT_BMALIBA :
-+					 (vendor == PCI_VENDOR_ID_VIA) ? DEFAULT_BMCRBA :
-+									DEFAULT_BMIBA)|1);
-+				if (pcibios_write_config_word(bus, fn, PCI_COMMAND, pcicmd|5) || rc)
- 					goto quit;
- 			}
- 		} while (try_again--);
-@@ -449,89 +680,308 @@ void ide_init_triton (byte bus, byte fn)
- 	/*
- 	 * See if ide port(s) are enabled
- 	 */
--	if ((rc = pcibios_read_config_dword(bus, fn, 0x40, &timings)))
--		goto quit;
--	if (!(timings & 0x80008000)) {
--		printk("ide: neither port is enabled\n");
-+	if ((rc = pcibios_read_config_dword(bus, fn,
-+		(vendor == PCI_VENDOR_ID_PROMISE) ? 0x50 : 
-+		(vendor == PCI_VENDOR_ID_ARTOP) ? 0x54 :
-+		(vendor == PCI_VENDOR_ID_SI) ? 0x48 :
-+		(vendor == PCI_VENDOR_ID_AL) ? 0x08 :
-+		0x40, &timings)))
- 		goto quit;
--	}
-+	/*
-+	 * We do a vendor check since the Ultra33/66 and AEC6210
-+	 * holds their timings in a different location.
-+	 */
-+#if 0
-+	printk("ide: timings == %08x\n", timings);
-+#endif
-+	/*
-+	 *  The switch preserves some stuff that was original.
-+	 */
-+	switch(vendor) {
-+		case PCI_VENDOR_ID_INTEL:
-+			if (!(timings & 0x80008000)) {
-+				printk("ide: INTEL: neither port is enabled\n");
-+				goto quit;
-+			}
-+			break;
-+		case PCI_VENDOR_ID_VIA:
-+			if(!(timings & 0x03)) {
-+				printk("ide: VIA: neither port is enabled\n");
-+				goto quit;
-+			}
-+			break;
-+		case PCI_VENDOR_ID_AL:
-+			timings <<= 16;
-+			timings >>= 24;
-+			if (!(timings & 0x30)) {
-+				printk("ide: ALI15X3: neither port is enabled\n");
-+				goto quit;
-+			}
-+			break;
-+		case PCI_VENDOR_ID_SI:
-+			timings <<= 8;
-+			timings >>= 24;
-+			if (!(timings & 0x06)) {
-+				printk("ide: SIS5513: neither port is enabled\n");
-+				goto quit;
-+			}
-+			break;
-+		case PCI_VENDOR_ID_PROMISE:
-+			printk("    (U)DMA Burst Bit %sABLED " \
-+				"Primary %s Mode " \
-+				"Secondary %s Mode.\n",
-+				(inb(bmiba + 0x001f) & 1) ? "EN" : "DIS",
-+				(inb(bmiba + 0x001a) & 1) ? "MASTER" : "PCI",
-+				(inb(bmiba + 0x001b) & 1) ? "MASTER" : "PCI" );
-+#if 0
-+			if (!(inb(bmiba + 0x001f) & 1)) {
-+				outb(inb(bmiba + 0x001f)|0x01, (bmiba + 0x001f));
-+				printk("    (U)DMA Burst Bit Forced %sABLED.\n",
-+					(inb(bmiba + 0x001f) & 1) ? "EN" : "DIS");
-+			}
-+#endif
-+			break;
-+		case PCI_VENDOR_ID_ARTOP:
-+		case PCI_VENDOR_ID_TTI:
-+                default:
-+                        break;
-+        }
- 
- 	/*
- 	 * Save the dma_base port addr for each interface
- 	 */
- 	for (h = 0; h < MAX_HWIFS; ++h) {
-+		ide_hwif_t *hwif = &ide_hwifs[h];
-+		byte channel = ((h == 1) || (h == 3) || (h == 5)) ? 1 : 0;
-+
-+		/*
-+		 *  This prevents the first contoller from accidentally
-+		 *  initalizing the hwif's that it does not use and block
-+		 *  an off-board ide-pci from getting in the game.
-+		 */
-+		if ((step_count >= 2) || (pass_count >= 2)) {
-+			goto quit;
-+		}
-+
-+#if 0
-+		if (hwif->chipset == ide_unknown)
-+			printk("ide: index == %d channel(%d)\n", h, channel);
-+#endif
-+
-+#ifdef CONFIG_BLK_DEV_OFFBOARD
-+		/*
-+		 *  This is a forced override for the onboard ide controller
-+		 *  to be enabled, if one chooses to have an offboard ide-pci
-+		 *  card as the primary booting device.  This beasty is
-+		 *  for offboard UDMA upgrades with hard disks, but saving
-+		 *  the onboard DMA2 controllers for CDROMS, TAPES, ZIPS, etc...
-+		 */
-+		if (((vendor == PCI_VENDOR_ID_INTEL) ||
-+		     (vendor == PCI_VENDOR_ID_SI) ||
-+		     (vendor == PCI_VENDOR_ID_VIA) ||
-+		     (vendor == PCI_VENDOR_ID_AL)) && (h >= 2)) {
-+			hwif->io_base	= channel ? 0x170 : 0x1f0;
-+			hwif->ctl_port	= channel ? 0x376 : 0x3f6;
-+			hwif->irq	= channel ? 15 : 14;
-+			hwif->noprobe	= 0;
-+		}
-+#endif /* CONFIG_BLK_DEV_OFFBOARD */
-+		/*
-+		 *  If the chipset is listed as "ide_unknown", lets get a
-+		 *  hwif while they last.  This does the first check on
-+		 *  the current availability of the ide_hwifs[h] in question.
-+		 */
-+		if (hwif->chipset != ide_unknown) {
-+			continue;
-+		} else if (vendor == PCI_VENDOR_ID_INTEL) {
-+			unsigned short time;
- #ifdef DISPLAY_TRITON_TIMINGS
--		byte s_clks, r_clks;
--		unsigned short devid;
-+			byte s_clks, r_clks;
-+			unsigned short devid;
- #endif /* DISPLAY_TRITON_TIMINGS */
--		ide_hwif_t *hwif = &ide_hwifs[h];
--		unsigned short time;
--		if (hwif->io_base == 0x1f0) {
--			time = timings & 0xffff;
--			if ((time & 0x8000) == 0)	/* interface enabled? */
--				continue;
--			hwif->chipset = ide_triton;
--			if (dma_enabled)
--				init_triton_dma(hwif, bmiba);
--		} else if (hwif->io_base == 0x170) {
--			time = timings >> 16;
--			if ((time & 0x8000) == 0)	/* interface enabled? */
-+			pass_count++;
-+			if (hwif->io_base == 0x1f0) {
-+				time = timings & 0xffff;
-+				if ((time & 0x8000) == 0)	/* interface enabled? */
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba);
-+				step_count++;
-+			} else if (hwif->io_base == 0x170) {
-+				time = timings >> 16;
-+				if ((time & 0x8000) == 0)	/* interface enabled? */
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba + 8);
-+				step_count++;
-+			} else {
- 				continue;
--			hwif->chipset = ide_triton;
--			if (dma_enabled)
--				init_triton_dma(hwif, bmiba + 8);
--		} else
--			continue;
-+			}
- #ifdef DISPLAY_TRITON_TIMINGS
--		s_clks = ((~time >> 12) & 3) + 2;
--		r_clks = ((~time >>  8) & 3) + 1;
--		printk("    %s timing: (0x%04x) sample_CLKs=%d, recovery_CLKs=%d\n",
--		 hwif->name, time, s_clks, r_clks);
--		if ((time & 0x40) && !pcibios_read_config_word(bus, fn, 0x02, &devid)
--		 && devid == PCI_DEVICE_ID_INTEL_82371SB_1)
--		{
--			byte stime;
--			if (pcibios_read_config_byte(bus, fn, 0x44, &stime)) {
--				if (hwif->io_base == 0x1f0) {
--					s_clks = ~stime >> 6;
--					r_clks = ~stime >> 4;
-+			s_clks = ((~time >> 12) & 3) + 2;
-+			r_clks = ((~time >>  8) & 3) + 1;
-+			printk("    %s timing: (0x%04x) sample_CLKs=%d, recovery_CLKs=%d\n",
-+				hwif->name, time, s_clks, r_clks);
-+			if ((time & 0x40) && !pcibios_read_config_word(bus, fn, PCI_DEVICE_ID, &devid)
-+				&& devid == PCI_DEVICE_ID_INTEL_82371SB_1) {
-+				byte stime;
-+				if (pcibios_read_config_byte(bus, fn, 0x44, &stime)) {
-+					if (hwif->io_base == 0x1f0) {
-+						s_clks = ~stime >> 6;
-+						r_clks = ~stime >> 4;
-+					} else {
-+						s_clks = ~stime >> 2;
-+						r_clks = ~stime;
-+					}
-+					s_clks = (s_clks & 3) + 2;
-+					r_clks = (r_clks & 3) + 1;
-+					printk("                   slave: sample_CLKs=%d, recovery_CLKs=%d\n",
-+						s_clks, r_clks);
-+				}
-+			}
-+			print_triton_drive_flags (0, time & 0xf);
-+			print_triton_drive_flags (1, (time >> 4) & 0xf);
-+#endif /* DISPLAY_TRITON_TIMINGS */
-+		} else if (vendor == PCI_VENDOR_ID_SI) {
-+			pass_count++;
-+			if (hwif->io_base == 0x1f0) {
-+				if ((timings & 0x02) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba);
-+				step_count++;
-+			} else if (hwif->io_base == 0x170) {
-+				if ((timings & 0x04) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba + 8);
-+				step_count++;
-+			} else {
-+				continue;
-+			}
-+		} else if (vendor == PCI_VENDOR_ID_VIA) {
-+			pass_count++;
-+			if (hwif->io_base == 0x1f0) {
-+				if ((timings & 0x02) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba);
-+				if (set_via_timings(bus, fn, 0xc0, 0xa0))
-+					goto quit;
-+#ifdef DISPLAY_APOLLO_TIMINGS
-+				proc_register_dynamic(&proc_root, &via_proc_entry);
-+#endif /* DISPLAY_APOLLO_TIMINGS */
-+				step_count++;
-+			} else if (hwif->io_base == 0x170) {
-+				if ((timings & 0x01) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba + 8);
-+				if (set_via_timings(bus, fn, 0x30, 0x50))
-+					goto quit;
-+				step_count++;
-+			} else {
-+				continue;
-+			}
-+		} else if (vendor == PCI_VENDOR_ID_AL) {
-+			byte ideic, inmir;
-+			byte irq_routing_table[] = { -1,  9, 3, 10, 4,  5, 7,  6,
-+						      1, 11, 0, 12, 0, 14, 0, 15 };
-+
-+			if (bridgeset) {
-+				pcibios_read_config_byte(bridgebus, bridgefn, 0x58, &ideic);
-+				ideic = ideic & 0x03;
-+				if ((channel && ideic == 0x03) || (!channel && !ideic)) {
-+					pcibios_read_config_byte(bridgebus, bridgefn, 0x44, &inmir);
-+					inmir = inmir & 0x0f;
-+					hwif->irq = irq_routing_table[inmir];
-+				} else if (channel && !(ideic & 0x01)) {
-+					pcibios_read_config_byte(bridgebus, bridgefn, 0x75, &inmir);
-+					inmir = inmir & 0x0f;
-+					hwif->irq = irq_routing_table[inmir];
-+				}
-+			}
-+			pass_count++;
-+			if (hwif->io_base == 0x1f0) {
-+				if ((timings & 0x20) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba);
-+				outb(inb(bmiba+2) & 0x60, bmiba+2);
-+				if (inb(bmiba+2) & 0x80)
-+					printk("ALI15X3: simplex device: DMA forced\n");
-+#ifdef DISPLAY_ALI15X3_TIMINGS
-+				proc_register_dynamic(&proc_root, &ali_proc_entry);
-+#endif /* DISPLAY_ALI15X3_TIMINGS */
-+				step_count++;
-+			} else if (hwif->io_base == 0x170) {
-+				if ((timings & 0x10) == 0)
-+					continue;
-+				hwif->chipset = ide_triton;
-+				if (dma_enabled)
-+					init_triton_dma(hwif, bmiba + 8);
-+				outb(inb(bmiba+10) & 0x60, bmiba+10);
-+				if (inb(bmiba+10) & 0x80)
-+					printk("ALI15X3: simplex device: DMA forced\n");
-+				step_count++;
-+			} else {
-+				continue;
-+			}
-+		} else if ((vendor == PCI_VENDOR_ID_PROMISE) ||
-+			   (vendor == PCI_VENDOR_ID_ARTOP) ||
-+			   (vendor == PCI_VENDOR_ID_TTI)) {
-+			pass_count++;
-+			if (vendor == PCI_VENDOR_ID_TTI) {
-+				if ((!hpt34x_flag) && (h < 2)) {
-+					goto quit;
-+				} else if (hpt34x_flag) {
-+					hwif->io_base	= channel ? (bmiba + 0x28) : (bmiba + 0x20);
-+					hwif->ctl_port	= channel ? (bmiba + 0x3e) : (bmiba + 0x36);
- 				} else {
--					s_clks = ~stime >> 2;
--					r_clks = ~stime;
-+					goto io_temps;
-+				}
-+			} else {
-+io_temps:
-+				tmp		= channel ? 2 : 0;
-+				hwif->io_base	= io[tmp];
-+				hwif->ctl_port	= io[tmp + 1] + 2;
-+			}
-+			hwif->irq = irq;
-+			hwif->noprobe = 0;
-+
-+			if (device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
-+				hwif->serialized = 1;
-+			}
-+
-+			if ((vendor == PCI_VENDOR_ID_PROMISE) ||
-+			    (vendor == PCI_VENDOR_ID_TTI)) {
-+				set_promise_hpt343_extra(device, bmiba);
-+			}
-+
-+			if (dma_enabled) {
-+				if ((!check_region(bmiba, 8)) && (!channel)) {
-+					hwif->chipset = ((vendor == PCI_VENDOR_ID_TTI) && !hpt34x_flag) ? ide_hpt343 :
-+							 (device == PCI_DEVICE_ID_PROMISE_20262) ? ide_ultra66 : ide_udma;
-+					init_triton_dma(hwif, bmiba);
-+					step_count++;
-+				} else if ((!check_region((bmiba + 0x08), 8)) && (channel)) {
-+					hwif->chipset = ((vendor == PCI_VENDOR_ID_TTI) && !hpt34x_flag) ? ide_hpt343 :
-+							 (device == PCI_DEVICE_ID_PROMISE_20262) ? ide_ultra66 : ide_udma;
-+					init_triton_dma(hwif, bmiba + 8);
-+					step_count++;
-+				} else {
-+					continue;
- 				}
--				s_clks = (s_clks & 3) + 2;
--				r_clks = (r_clks & 3) + 1;
--				printk("                   slave: sample_CLKs=%d, recovery_CLKs=%d\n",
--		 			s_clks, r_clks);
- 			}
- 		}
--		print_triton_drive_flags (0, time & 0xf);
--		print_triton_drive_flags (1, (time >> 4) & 0xf);
--#endif /* DISPLAY_TRITON_TIMINGS */
- 	}
- 
--quit: if (rc) printk("ide: pcibios access failed - %s\n", pcibios_strerror(rc));
--}
--
--void ide_init_promise (byte bus, byte fn, ide_hwif_t *hwif0, ide_hwif_t *hwif1, unsigned short dma)
--{
--	int rc;
--	unsigned short pcicmd;
--	unsigned int bmiba = 0;
--
--	printk("ide: Enabling DMA for Promise Technology IDE Ultra-DMA 33 on PCI bus %d function %d, port 0x%04x\n", bus, fn, dma);
--	if ((rc = pcibios_read_config_word(bus, fn, 0x04, &pcicmd)) || (pcicmd & 1) == 0 || (pcicmd & 4) == 0)
--		goto abort;
--	if ((rc = pcibios_read_config_dword(bus, fn, 0x20, &bmiba)))
--		goto abort;
--	bmiba &= 0xfff0;	/* extract port base address */
--	if (bmiba != dma || !bmiba)
--		goto abort;
--	hwif0->chipset = ide_promise_udma;
--	hwif1->chipset = ide_promise_udma;
--	init_triton_dma(hwif0, bmiba);
--	init_triton_dma(hwif1, bmiba + 0x08);
--	return;
--abort:
--	printk(KERN_WARNING "ide: Promise/33 not configured correctly (BIOS)\n");
-+	quit: if (rc) printk("ide: pcibios access failed - %s\n", pcibios_strerror(rc));
- }
-Index: b/linux/src/include/linux/hdreg.h
-===================================================================
---- a/linux/src/include/linux/hdreg.h
-+++ b/linux/src/include/linux/hdreg.h
-@@ -92,11 +92,12 @@ struct hd_geometry {
- #define HDIO_GETGEO		0x0301	/* get device geometry */
- #define HDIO_GET_UNMASKINTR	0x0302	/* get current unmask setting */
- #define HDIO_GET_MULTCOUNT	0x0304	/* get current IDE blockmode setting */
--#define HDIO_GET_IDENTITY 	0x0307	/* get IDE identification info */
-+#define HDIO_OBSOLETE_IDENTITY	0x0307	/* OBSOLETE, DO NOT USE: returns 142 bytes */
- #define HDIO_GET_KEEPSETTINGS 	0x0308	/* get keep-settings-on-reset flag */
- #define HDIO_GET_32BIT 		0x0309	/* get current io_32bit setting */
- #define HDIO_GET_NOWERR		0x030a	/* get ignore-write-error flag */
- #define HDIO_GET_DMA		0x030b	/* get use-dma flag */
-+#define HDIO_GET_IDENTITY	0x030d	/* get IDE identification info */
- #define HDIO_DRIVE_CMD		0x031f	/* execute a special drive command */
- 
- /* hd/ide ctl's that pass (arg) non-ptr values are numbered 0x032n/0x033n */
-@@ -166,14 +167,54 @@ struct hd_driveid {
- 	unsigned short  word79;
- 	unsigned short  word80;
- 	unsigned short  word81;
--	unsigned short  word82;
--	unsigned short  word83;
-+	unsigned short  command_sets;	/* bits 0:Smart 1:Security 2:Removable 3:PM */
-+	unsigned short  word83;		/* bits 14:Smart Enabled 13:0 zero */
- 	unsigned short  word84;
- 	unsigned short  word85;
- 	unsigned short  word86;
- 	unsigned short  word87;
- 	unsigned short  dma_ultra;
--	unsigned short  reserved[167];
-+	unsigned short	word89;		/* reserved (word 89) */
-+	unsigned short	word90;		/* reserved (word 90) */
-+	unsigned short	word91;		/* reserved (word 91) */
-+	unsigned short	word92;		/* reserved (word 92) */
-+	unsigned short	word93;		/* reserved (word 93) */
-+	unsigned short	word94;		/* reserved (word 94) */
-+	unsigned short	word95;		/* reserved (word 95) */
-+	unsigned short	word96;		/* reserved (word 96) */
-+	unsigned short	word97;		/* reserved (word 97) */
-+	unsigned short	word98;		/* reserved (word 98) */
-+	unsigned short	word99;		/* reserved (word 99) */
-+	unsigned short	word100;	/* reserved (word 100) */
-+	unsigned short	word101;	/* reserved (word 101) */
-+	unsigned short	word102;	/* reserved (word 102) */
-+	unsigned short	word103;	/* reserved (word 103) */
-+	unsigned short	word104;	/* reserved (word 104) */
-+	unsigned short	word105;	/* reserved (word 105) */
-+	unsigned short	word106;	/* reserved (word 106) */
-+	unsigned short	word107;	/* reserved (word 107) */
-+	unsigned short	word108;	/* reserved (word 108) */
-+	unsigned short	word109;	/* reserved (word 109) */
-+	unsigned short	word110;	/* reserved (word 110) */
-+	unsigned short	word111;	/* reserved (word 111) */
-+	unsigned short	word112;	/* reserved (word 112) */
-+	unsigned short	word113;	/* reserved (word 113) */
-+	unsigned short	word114;	/* reserved (word 114) */
-+	unsigned short	word115;	/* reserved (word 115) */
-+	unsigned short	word116;	/* reserved (word 116) */
-+	unsigned short	word117;	/* reserved (word 117) */
-+	unsigned short	word118;	/* reserved (word 118) */
-+	unsigned short	word119;	/* reserved (word 119) */
-+	unsigned short	word120;	/* reserved (word 120) */
-+	unsigned short	word121;	/* reserved (word 121) */
-+	unsigned short	word122;	/* reserved (word 122) */
-+	unsigned short	word123;	/* reserved (word 123) */
-+	unsigned short	word124;	/* reserved (word 124) */
-+	unsigned short	word125;	/* reserved (word 125) */
-+	unsigned short	word126;	/* reserved (word 126) */
-+	unsigned short	word127;	/* reserved (word 127) */
-+	unsigned short	security;	/* bits 0:suuport 1:enabled 2:locked 3:frozen */
-+	unsigned short	reserved[127];
- };
- 
- #ifdef __KERNEL__
-Index: b/linux/configfrag.ac
-===================================================================
---- a/linux/configfrag.ac
-+++ b/linux/configfrag.ac
-@@ -140,6 +140,11 @@ AC_Linux_DRIVER_qemu([ide],
-   [IDE disk controllers],
-   [CONFIG_BLK_DEV_IDE])
- 
-+AC_ARG_ENABLE([ide-forcedma],
-+  AS_HELP_STRING([--enable-ide-forcedma], [enable forced use of DMA on IDE]),
-+  [test x"$enableval" = xno ||
-+   AC_DEFINE([CONFIG_BLK_DEV_FORCE_DMA], [1], [Force DMA on IDE block devices])])
-+
- dnl SCSI controllers.
- AC_OPTION_Linux_group([scsi], [SCSI drivers])
- 
diff --git a/debian/patches/24_pci_irq_fix.patch b/debian/patches/24_pci_irq_fix.patch
deleted file mode 100644
index cba0cab..0000000
--- a/debian/patches/24_pci_irq_fix.patch
+++ /dev/null
@@ -1,33 +0,0 @@
-My laptop's motherboard set its RTL8139 NIC IRQ at a value that is not
-included in the range 0<=x<16 and it's not 255.
-
-GNU Mach can't handle that, and when I try a 'devprobe eth0' I get a
-panic due to a failed assert (irq < 16). This patch tell GNU Mach to
-ignore this kind of IRQ.
-
-The real solution for this problem would be an PCI IRQ Router, which
-is what I am going to port/implement in Mach soon. For now, this patch
-helps by both removing the failed assert and by noticing the user that
-the device is not being used for unassigned IRQ.
-
-
-2006-01-28  Gianluca Guida  <glguida@gmail.com>
-
-	* linux/src/drivers/net/pci-scan.c (pci_drv_register): Skip device
-	if we are getting an invalid IRQ >= 16 and different from 255 (it
-	happens in some motherboard).
-
-
-Index: b/linux/src/drivers/net/pci-scan.c
-===================================================================
---- a/linux/src/drivers/net/pci-scan.c
-+++ b/linux/src/drivers/net/pci-scan.c
-@@ -347,7 +347,7 @@ int pci_drv_register(struct drv_id_info 
- 				   pci_tbl[chip_idx].name, pciaddr, irq);
- 
- 		if ( ! (pci_flags & PCI_UNUSED_IRQ)  &&
--			 (irq == 0 || irq == 255)) {
-+			 (irq == 0 || irq >= 16)) {
- 			if (pci_bus == 32) 	/* Broken CardBus activation. */
- 				printk(KERN_WARNING "Resources for CardBus device '%s' have"
- 					   " not been allocated.\n"
diff --git a/debian/patches/series b/debian/patches/series
index e8eb4db..8433870 100644
--- a/debian/patches/series
+++ b/debian/patches/series
@@ -1,9 +1,6 @@
 00_clean_gfdl.patch
-10_cdromlock.patch
 11_ignore_CSIn.patch
 12_version_suffix.patch
-13_ide_dma.patch
-24_pci_irq_fix.patch
 50_initrd.patch
 60_bigmem.patch
 70_dde.patch