path: root/linux/src/drivers/net/ne2k-pci.c

/* ne2k-pci.c: A NE2000 clone on PCI bus driver for Linux. */
/*
	A Linux device driver for PCI NE2000 clones.

	Authors and other copyright holders:
	1992-2002 by Donald Becker, NE2000 core and various modifications.
	1995-1998 by Paul Gortmaker, core modifications and PCI support.
	Copyright 1993 assigned to the United States Government as represented
	by the Director, National Security Agency.

	This software may be used and distributed according to the terms of
	the GNU General Public License (GPL), incorporated herein by reference.
	Drivers based on or derived from this code fall under the GPL and must
	retain the authorship, copyright and license notice.  This file is not
	a complete program and may only be used when the entire operating
	system is licensed under the GPL.

	The author may be reached as becker@scyld.com, or C/O
	Scyld Computing Corporation
	410 Severn Ave., Suite 210
	Annapolis MD 21403

	Issues remaining:
	People are making PCI ne2000 clones! Oh the horror, the horror...
	Limited full-duplex support.
*/

/* These identify the driver base version and may not be removed. */
static const char version1[] =
"ne2k-pci.c:v1.05 6/13/2002 D. Becker/P. Gortmaker\n";
static const char version2[] =
"  http://www.scyld.com/network/ne2k-pci.html\n";

/* The user-configurable values.
   These may be modified when a driver module is loaded.*/

static int debug = 1;			/* 1 normal messages, 0 quiet .. 7 verbose. */

#define MAX_UNITS 8				/* More are supported, limit only on options */
/* Used to pass the full-duplex flag, etc. */
static int full_duplex[MAX_UNITS] = {0, };
static int options[MAX_UNITS] = {0, };

/* Force a non std. amount of memory.  Units are 256 byte pages. */
/* #define PACKETBUF_MEMSIZE	0x40 */

#ifndef __KERNEL__
#define __KERNEL__
#endif
#if !defined(__OPTIMIZE__)
#warning  You must compile this file with the correct options!
#warning  See the last lines of the source file.
#error You must compile this driver with "-O".
#endif

#include <linux/config.h>
#if defined(CONFIG_SMP) && ! defined(__SMP__)
#define __SMP__
#endif
#if defined(MODULE) && defined(CONFIG_MODVERSIONS) && ! defined(MODVERSIONS)
#define MODVERSIONS
#endif

#include <linux/version.h>
#include <linux/module.h>
#if LINUX_VERSION_CODE < 0x20300  &&  defined(MODVERSIONS)
#include <linux/modversions.h>
#endif

#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/pci.h>
#if LINUX_VERSION_CODE < 0x20200
#define lock_8390_module()
#define unlock_8390_module()
#else
#include <linux/init.h>
#endif

#include <asm/system.h>
#include <asm/io.h>
#include <asm/irq.h>

#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include "8390.h"

#ifdef INLINE_PCISCAN
#include "k_compat.h"
#else
#include "pci-scan.h"
#include "kern_compat.h"
#endif

MODULE_AUTHOR("Donald Becker / Paul Gortmaker");
MODULE_DESCRIPTION("PCI NE2000 clone driver");
MODULE_PARM(debug, "i");
MODULE_PARM(options, "1-" __MODULE_STRING(MAX_UNITS) "i");
MODULE_PARM(full_duplex, "1-" __MODULE_STRING(MAX_UNITS) "i");

/* Some defines that people can play with if so inclined. */

/* Do #define LOAD_8390_BY_KERNELD to automatically load 8390 support. */
#ifdef LOAD_8390_BY_KERNELD
#include <linux/kerneld.h>
#endif

static void *ne2k_pci_probe1(struct pci_dev *pdev, void *dev,
							 long ioaddr, int irq, int chip_idx, int fnd_cnt);
/* Flags.  We rename an existing ei_status field to store flags! */
/* Thus only the low 8 bits are usable for non-init-time flags. */
#define ne2k_flags reg0
enum {
	ONLY_16BIT_IO=8, ONLY_32BIT_IO=4,	/* Chip can do only 16/32-bit xfers. */
	FORCE_FDX=0x20,						/* User override. */
	REALTEK_FDX=0x40, HOLTEK_FDX=0x80,
	STOP_PG_0x60=0x100,
};
#define NE_IO_EXTENT	0x20
#ifndef USE_MEMORY_OPS
#define PCI_IOTYPE (PCI_USES_IO  | PCI_ADDR0)
#else
#warning When using PCI memory mode the 8390 core must be compiled for memory
#warning operations as well.
#warning Not all PCI NE2000 clones support memory mode access. 
#define PCI_IOTYPE (PCI_USES_MEM | PCI_ADDR1)
#endif

static struct pci_id_info pci_id_tbl[] = {
	{"RealTek RTL-8029",{ 0x802910ec, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT,
	 REALTEK_FDX },
	{"Winbond 89C940",  { 0x09401050, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	{"Winbond w89c940",	{ 0x5a5a1050, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	{"KTI ET32P2",      { 0x30008e2e, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	{"NetVin NV5000SC", { 0x50004a14, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	{"Via 86C926",		{ 0x09261106, 0xffffffff},
	 PCI_IOTYPE, NE_IO_EXTENT, ONLY_16BIT_IO},
	{"SureCom NE34",	{ 0x0e3410bd, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	{"Holtek HT80232",	{ 0x005812c3, 0xffffffff},
	 PCI_IOTYPE, NE_IO_EXTENT, ONLY_16BIT_IO | HOLTEK_FDX},
	{"Holtek HT80229",	{ 0x559812c3, 0xffffffff},
	 PCI_IOTYPE, NE_IO_EXTENT, ONLY_32BIT_IO | HOLTEK_FDX | STOP_PG_0x60},
	{"Compex RL2000",
	 { 0x140111f6, 0xffffffff}, PCI_IOTYPE, NE_IO_EXTENT, 0},
	/* A mutant board: Winbond chip with a RTL format EEPROM. */
	{"Winbond w89c940 (misprogrammed type 0x1980)", { 0x19808c4a, 0xffffffff},
	 PCI_IOTYPE, NE_IO_EXTENT, 0},
	{0,},						/* 0 terminated list. */
};

struct drv_id_info ne2k_pci_drv_id = {
	"ne2k-pci", 0, PCI_CLASS_NETWORK_ETHERNET<<8, pci_id_tbl, ne2k_pci_probe1,
};

/* ---- No user-serviceable parts below ---- */

#define NE_BASE	 (dev->base_addr)
#define NE_CMD	 	0x00
#define NE_DATAPORT	0x10	/* NatSemi-defined port window offset. */
#define NE_RESET	0x1f	/* Issue a read to reset, a write to clear. */

#define NESM_START_PG	0x40	/* First page of TX buffer */
#define NESM_STOP_PG	0x80	/* Last page +1 of RX ring */

int ne2k_pci_probe(struct net_device *dev);

static int ne2k_pci_open(struct net_device *dev);
static int ne2k_pci_close(struct net_device *dev);

static void ne2k_pci_reset_8390(struct net_device *dev);
static void ne2k_pci_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
			  int ring_page);
static void ne2k_pci_block_input(struct net_device *dev, int count,
			  struct sk_buff *skb, int ring_offset);
static void ne2k_pci_block_output(struct net_device *dev, const int count,
		const unsigned char *buf, const int start_page);



/* There is no room in the standard 8390 structure for extra info we need,
   so we build a meta/outer-wrapper structure.. */
struct ne2k_pci_card {
	struct ne2k_pci_card *next;
	struct net_device *dev;
	struct pci_dev *pci_dev;
};
/* A list of all installed devices, for removing the driver module. */
static struct ne2k_pci_card *ne2k_card_list = NULL;

#ifdef LOAD_8390_BY_KERNELD
static int (*Lethdev_init)(struct net_device *dev);
static void (*LNS8390_init)(struct net_device *dev, int startp);
static int (*Lei_open)(struct net_device *dev);
static int (*Lei_close)(struct net_device *dev);
static void (*Lei_interrupt)(int irq, void *dev_id, struct pt_regs *regs);
#else
#define Lethdev_init ethdev_init
#define LNS8390_init NS8390_init
#define Lei_open ei_open
#define Lei_close ei_close
#define Lei_interrupt ei_interrupt
#endif

#ifdef MODULE
int init_module(void)
{
	int found_cnt;

	if (debug)					/* Emit version even if no cards detected. */
		printk(KERN_INFO "%s" KERN_INFO "%s", version1, version2);
	found_cnt = pci_drv_register(&ne2k_pci_drv_id, NULL);
	if (found_cnt < 0) {
		printk(KERN_NOTICE "ne2k-pci.c: No useable cards found, driver NOT installed.\n");
		return -ENODEV;
	}
	lock_8390_module();
	return 0;
}

void cleanup_module(void)
{
	struct net_device *dev;
	struct ne2k_pci_card *this_card;

	pci_drv_unregister(&ne2k_pci_drv_id);

	/* No need to check MOD_IN_USE, as sys_delete_module() checks. */
	while (ne2k_card_list) {
		dev = ne2k_card_list->dev;
		unregister_netdev(dev);
		release_region(dev->base_addr, NE_IO_EXTENT);
		kfree(dev);
		this_card = ne2k_card_list;
		ne2k_card_list = ne2k_card_list->next;
		kfree(this_card);
	}

#ifdef LOAD_8390_BY_KERNELD
	release_module("8390", 0);
#else
	unlock_8390_module();
#endif
}

#else

int ne2k_pci_probe(struct net_device *dev)
{
	int found_cnt = pci_drv_register(&ne2k_pci_drv_id, NULL);
	if (found_cnt >= 0  &&  debug)
		printk(KERN_INFO "%s" KERN_INFO "%s", version1, version2);
	return found_cnt;
}
#endif  /* MODULE */

static void *ne2k_pci_probe1(struct pci_dev *pdev, void *init_dev,
							 long ioaddr, int irq, int chip_idx, int fnd_cnt)
{
	struct net_device *dev;
	int i;
	unsigned char SA_prom[32];
	int start_page, stop_page;
	int reg0 = inb(ioaddr);
	int flags = pci_id_tbl[chip_idx].drv_flags;
	struct ne2k_pci_card *ne2k_card;

	if (reg0 == 0xFF)
		return 0;

	/* Do a preliminary verification that we have a 8390. */
	{
		int regd;
		outb(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD);
		regd = inb(ioaddr + 0x0d);
		outb(0xff, ioaddr + 0x0d);
		outb(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD);
		inb(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */
		if (inb(ioaddr + EN0_COUNTER0) != 0) {
			outb(reg0, ioaddr);
			outb(regd, ioaddr + 0x0d);	/* Restore the old values. */
			return 0;
		}
	}

	dev = init_etherdev(init_dev, 0);

	if (dev == NULL)
		return 0;
	ne2k_card = kmalloc(sizeof(struct ne2k_pci_card), GFP_KERNEL);
	if (ne2k_card == NULL)
		return 0;

	ne2k_card->next = ne2k_card_list;
	ne2k_card_list = ne2k_card;
	ne2k_card->dev = dev;
	ne2k_card->pci_dev = pdev;

	/* Reset card. Who knows what dain-bramaged state it was left in. */
	{
		unsigned long reset_start_time = jiffies;

		outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET);

		/* This looks like a horrible timing loop, but it should never take
		   more than a few cycles.
		*/
		while ((inb(ioaddr + EN0_ISR) & ENISR_RESET) == 0)
			/* Limit wait: '2' avoids jiffy roll-over. */
			if (jiffies - reset_start_time > 2) {
				printk("ne2k-pci: Card failure (no reset ack).\n");
				return 0;
			}
		
		outb(0xff, ioaddr + EN0_ISR);		/* Ack all intr. */
	}

#if defined(LOAD_8390_BY_KERNELD)
	/* We are now certain the 8390 module is required. */
	if (request_module("8390")) {
		printk("ne2k-pci: Failed to load the 8390 core module.\n");
		return 0;
	}
	if ((Lethdev_init = (void*)get_module_symbol(0, "ethdev_init")) == 0 ||
		(LNS8390_init = (void*)get_module_symbol(0, "NS8390_init")) == 0 ||
		(Lei_open = (void*)get_module_symbol(0, "ei_open")) == 0 ||
		(Lei_close = (void*)get_module_symbol(0, "ei_close")) == 0 ||
		(Lei_interrupt = (void*)get_module_symbol(0, "ei_interrupt")) == 0 ) {
		printk("ne2k-pci: Failed to resolve an 8390 symbol.\n");
		release_module("8390", 0);
		return 0;
	}
#endif

	/* Read the 16 bytes of station address PROM.
	   We must first initialize registers, similar to NS8390_init(eifdev, 0).
	   We can't reliably read the SAPROM address without this.
	   (I learned the hard way!). */
	{
		struct {unsigned char value, offset; } program_seq[] = {
			{E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
			{0x49,	EN0_DCFG},	/* Set word-wide access. */
			{0x00,	EN0_RCNTLO},	/* Clear the count regs. */
			{0x00,	EN0_RCNTHI},
			{0x00,	EN0_IMR},	/* Mask completion irq. */
			{0xFF,	EN0_ISR},
			{E8390_RXOFF, EN0_RXCR},	/* 0x20  Set to monitor */
			{E8390_TXOFF, EN0_TXCR},	/* 0x02  and loopback mode. */
			{32,	EN0_RCNTLO},
			{0x00,	EN0_RCNTHI},
			{0x00,	EN0_RSARLO},	/* DMA starting at 0x0000. */
			{0x00,	EN0_RSARHI},
			{E8390_RREAD+E8390_START, E8390_CMD},
		};
		for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
			outb(program_seq[i].value, ioaddr + program_seq[i].offset);

	}

	/* Note: all PCI cards have at least 16 bit access, so we don't have
	   to check for 8 bit cards.  Most cards permit 32 bit access. */

	if (flags & ONLY_32BIT_IO) {
		for (i = 0; i < 8; i++)
			((u32 *)SA_prom)[i] = le32_to_cpu(inl(ioaddr + NE_DATAPORT));
	} else
		for(i = 0; i < 32 /*sizeof(SA_prom)*/; i++)
			SA_prom[i] = inb(ioaddr + NE_DATAPORT);

	/* We always set the 8390 registers for word mode. */
	outb(0x49, ioaddr + EN0_DCFG);
	start_page = NESM_START_PG;

	stop_page = flags & STOP_PG_0x60 ? 0x60 : NESM_STOP_PG;

	/* Set up the rest of the parameters. */
	dev->irq = irq;
	dev->base_addr = ioaddr;

	/* Allocate dev->priv and fill in 8390 specific dev fields. */
	if (Lethdev_init(dev)) {
		printk ("%s: unable to get memory for dev->priv.\n", dev->name);
		return 0;
	}

	request_region(ioaddr, NE_IO_EXTENT, dev->name);

	printk("%s: %s found at %#lx, IRQ %d, ",
		   dev->name, pci_id_tbl[chip_idx].name, ioaddr, dev->irq);
	for(i = 0; i < 6; i++) {
		printk("%2.2X%s", SA_prom[i], i == 5 ? ".\n": ":");
		dev->dev_addr[i] = SA_prom[i];
	}

	ei_status.name = pci_id_tbl[chip_idx].name;
	ei_status.tx_start_page = start_page;
	ei_status.stop_page = stop_page;
	ei_status.word16 = 1;
	ei_status.ne2k_flags = flags;
	if (fnd_cnt < MAX_UNITS) {
		if (full_duplex[fnd_cnt] > 0  ||  (options[fnd_cnt] & FORCE_FDX)) {
			printk("%s:  Full duplex set by user option.\n", dev->name);
			ei_status.ne2k_flags |= FORCE_FDX;
		}
	}

	ei_status.rx_start_page = start_page + TX_PAGES;
#ifdef PACKETBUF_MEMSIZE
	/* Allow the packet buffer size to be overridden by know-it-alls. */
	ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE;
#endif

	ei_status.reset_8390 = &ne2k_pci_reset_8390;
	ei_status.block_input = &ne2k_pci_block_input;
	ei_status.block_output = &ne2k_pci_block_output;
	ei_status.get_8390_hdr = &ne2k_pci_get_8390_hdr;
	dev->open = &ne2k_pci_open;
	dev->stop = &ne2k_pci_close;
	LNS8390_init(dev, 0);
	return dev;
}

static int ne2k_pci_open(struct net_device *dev)
{
	MOD_INC_USE_COUNT;
	if (request_irq(dev->irq, Lei_interrupt, SA_SHIRQ, dev->name, dev)) {
		MOD_DEC_USE_COUNT;
		return -EAGAIN;
	}
	/* Set full duplex for the chips that we know about. */
	if (ei_status.ne2k_flags & FORCE_FDX) {
		long ioaddr = dev->base_addr;
		if (ei_status.ne2k_flags & REALTEK_FDX) {
			outb(0xC0 + E8390_NODMA, ioaddr + NE_CMD); /* Page 3 */
			outb(inb(ioaddr + 0x20) | 0x80, ioaddr + 0x20);
		} else if (ei_status.ne2k_flags & HOLTEK_FDX)
			outb(inb(ioaddr + 0x20) | 0x80, ioaddr + 0x20);
	}
	Lei_open(dev);
	return 0;
}

static int ne2k_pci_close(struct net_device *dev)
{
	Lei_close(dev);
	free_irq(dev->irq, dev);
	MOD_DEC_USE_COUNT;
	return 0;
}

/* Hard reset the card.  This used to pause for the same period that a
   8390 reset command required, but that shouldn't be necessary. */
static void ne2k_pci_reset_8390(struct net_device *dev)
{
	unsigned long reset_start_time = jiffies;

	if (debug > 1) printk("%s: Resetting the 8390 t=%ld...",
						  dev->name, jiffies);

	outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);

	ei_status.txing = 0;
	ei_status.dmaing = 0;

	/* This check _should_not_ be necessary, omit eventually. */
	while ((inb(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
		if (jiffies - reset_start_time > 2) {
			printk("%s: ne2k_pci_reset_8390() did not complete.\n", dev->name);
			break;
		}
	outb(ENISR_RESET, NE_BASE + EN0_ISR);	/* Ack intr. */
}

/* Grab the 8390 specific header. Similar to the block_input routine, but
   we don't need to be concerned with ring wrap as the header will be at
   the start of a page, so we optimize accordingly. */

static void ne2k_pci_get_8390_hdr(struct net_device *dev,
								  struct e8390_pkt_hdr *hdr, int ring_page)
{

	long nic_base = dev->base_addr;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_get_8390_hdr "
			   "[DMAstat:%d][irqlock:%d][intr:%d].\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock,
			   (int)dev->interrupt);
		return;
	}

	ei_status.dmaing |= 0x01;
	outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
	outb(sizeof(struct e8390_pkt_hdr), nic_base + EN0_RCNTLO);
	outb(0, nic_base + EN0_RCNTHI);
	outb(0, nic_base + EN0_RSARLO);		/* On page boundary */
	outb(ring_page, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);

	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		insw(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)>>1);
	} else {
		*(u32*)hdr = le32_to_cpu(inl(NE_BASE + NE_DATAPORT));
		le16_to_cpus(&hdr->count);
	}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
}

/* Block input and output, similar to the Crynwr packet driver.  If you
   are porting to a new ethercard, look at the packet driver source for hints.
   The NEx000 doesn't share the on-board packet memory -- you have to put
   the packet out through the "remote DMA" dataport using outb. */

static void ne2k_pci_block_input(struct net_device *dev, int count,
								 struct sk_buff *skb, int ring_offset)
{
	long nic_base = dev->base_addr;
	char *buf = skb->data;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_block_input "
			   "[DMAstat:%d][irqlock:%d][intr:%d].\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock,
			   (int)dev->interrupt);
		return;
	}
	ei_status.dmaing |= 0x01;
	if (ei_status.ne2k_flags & ONLY_32BIT_IO)
		count = (count + 3) & 0xFFFC;
	outb(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
	outb(count & 0xff, nic_base + EN0_RCNTLO);
	outb(count >> 8, nic_base + EN0_RCNTHI);
	outb(ring_offset & 0xff, nic_base + EN0_RSARLO);
	outb(ring_offset >> 8, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);

	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		insw(NE_BASE + NE_DATAPORT,buf,count>>1);
		if (count & 0x01) {
			buf[count-1] = inb(NE_BASE + NE_DATAPORT);
		}
	} else {
		insl(NE_BASE + NE_DATAPORT, buf, count>>2);
		if (count & 3) {
			buf += count & ~3;
			if (count & 2) {
				*((u16 *) buf) = le16_to_cpu(inw(NE_BASE + NE_DATAPORT));
				buf = (void *) buf + sizeof (u16);
			}
			if (count & 1)
				*buf = inb(NE_BASE + NE_DATAPORT);
		}
	}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
}

static void
ne2k_pci_block_output(struct net_device *dev, int count,
		const unsigned char *buf, const int start_page)
{
	int nic_base = NE_BASE;
	unsigned long dma_start;

	/* On little-endian it's always safe to round the count up for
	   word writes. */
	if (ei_status.ne2k_flags & ONLY_32BIT_IO)
		count = (count + 3) & 0xFFFC;
	else
		if (count & 0x01)
			count++;

	/* This *shouldn't* happen. If it does, it's the last thing you'll see */
	if (ei_status.dmaing) {
		printk("%s: DMAing conflict in ne2k_pci_block_output."
			   "[DMAstat:%d][irqlock:%d][intr:%d]\n",
			   dev->name, ei_status.dmaing, ei_status.irqlock,
			   (int)dev->interrupt);
		return;
	}
	ei_status.dmaing |= 0x01;
	/* We should already be in page 0, but to be safe... */
	outb(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base + NE_CMD);

#ifdef NE8390_RW_BUGFIX
	/* Handle the read-before-write bug the same way as the
	   Crynwr packet driver -- the NatSemi method doesn't work.
	   Actually this doesn't always work either, but if you have
	   problems with your NEx000 this is better than nothing! */
	outb(0x42, nic_base + EN0_RCNTLO);
	outb(0x00, nic_base + EN0_RCNTHI);
	outb(0x42, nic_base + EN0_RSARLO);
	outb(0x00, nic_base + EN0_RSARHI);
	outb(E8390_RREAD+E8390_START, nic_base + NE_CMD);
#endif
	outb(ENISR_RDC, nic_base + EN0_ISR);

   /* Now the normal output. */
	outb(count & 0xff, nic_base + EN0_RCNTLO);
	outb(count >> 8,   nic_base + EN0_RCNTHI);
	outb(0x00, nic_base + EN0_RSARLO);
	outb(start_page, nic_base + EN0_RSARHI);
	outb(E8390_RWRITE+E8390_START, nic_base + NE_CMD);
	if (ei_status.ne2k_flags & ONLY_16BIT_IO) {
		outsw(NE_BASE + NE_DATAPORT, buf, count>>1);
	} else {
		outsl(NE_BASE + NE_DATAPORT, buf, count>>2);
		if (count & 3) {
			buf += count & ~3;
			if (count & 2) {
				outw(cpu_to_le16(*((u16 *) buf)), NE_BASE + NE_DATAPORT);
				buf = (void *) buf + sizeof (u16);
			}
		}
	}

	dma_start = jiffies;

	while ((inb(nic_base + EN0_ISR) & ENISR_RDC) == 0)
		if (jiffies - dma_start > 2) { 			/* Avoid clock roll-over. */
			printk("%s: timeout waiting for Tx RDC.\n", dev->name);
			ne2k_pci_reset_8390(dev);
			LNS8390_init(dev,1);
			break;
		}

	outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
	ei_status.dmaing &= ~0x01;
	return;
}


/*
 * Local variables:
 *  compile-command: "gcc -DMODULE -Wall -Wstrict-prototypes -O6 -c ne2k-pci.c  -I/usr/src/linux/drivers/net/"
 *  alt-compile-command: "gcc -DMODULE -O6 -c ne2k-pci.c"
 *  c-indent-level: 4
 *  c-basic-offset: 4
 *  tab-width: 4
 *  version-control: t
 *  kept-new-versions: 5
 * End:
 */