1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
|
/*****************************************************************
*
* defines for 3Com Etherlink Plus adapter
*
*****************************************************************/
/*
* I/O register offsets
*/
#define PORT_COMMAND 0x00 /* read/write, 8-bit */
#define PORT_STATUS 0x02 /* read only, 8-bit */
#define PORT_AUXDMA 0x02 /* write only, 8-bit */
#define PORT_DATA 0x04 /* read/write, 16-bit */
#define PORT_CONTROL 0x06 /* read/write, 8-bit */
#define ELP_IO_EXTENT 0x10 /* size of used IO registers */
/*
* host control registers bits
*/
#define ATTN 0x80 /* attention */
#define FLSH 0x40 /* flush data register */
#define DMAE 0x20 /* DMA enable */
#define DIR 0x10 /* direction */
#define TCEN 0x08 /* terminal count interrupt enable */
#define CMDE 0x04 /* command register interrupt enable */
#define HSF2 0x02 /* host status flag 2 */
#define HSF1 0x01 /* host status flag 1 */
/*
* combinations of HSF flags used for PCB transmission
*/
#define HSF_PCB_ACK HSF1
#define HSF_PCB_NAK HSF2
#define HSF_PCB_END (HSF2|HSF1)
#define HSF_PCB_MASK (HSF2|HSF1)
/*
* host status register bits
*/
#define HRDY 0x80 /* data register ready */
#define HCRE 0x40 /* command register empty */
#define ACRF 0x20 /* adapter command register full */
/* #define DIR 0x10 direction - same as in control register */
#define DONE 0x08 /* DMA done */
#define ASF3 0x04 /* adapter status flag 3 */
#define ASF2 0x02 /* adapter status flag 2 */
#define ASF1 0x01 /* adapter status flag 1 */
/*
* combinations of ASF flags used for PCB reception
*/
#define ASF_PCB_ACK ASF1
#define ASF_PCB_NAK ASF2
#define ASF_PCB_END (ASF2|ASF1)
#define ASF_PCB_MASK (ASF2|ASF1)
/*
* host aux DMA register bits
*/
#define DMA_BRST 0x01 /* DMA burst */
/*
* maximum amount of data allowed in a PCB
*/
#define MAX_PCB_DATA 62
/*****************************************************************
*
* timeout value
* this is a rough value used for loops to stop them from
* locking up the whole machine in the case of failure or
* error conditions
*
*****************************************************************/
#define TIMEOUT 300
/*****************************************************************
*
* PCB commands
*
*****************************************************************/
enum {
/*
* host PCB commands
*/
CMD_CONFIGURE_ADAPTER_MEMORY = 0x01,
CMD_CONFIGURE_82586 = 0x02,
CMD_STATION_ADDRESS = 0x03,
CMD_DMA_DOWNLOAD = 0x04,
CMD_DMA_UPLOAD = 0x05,
CMD_PIO_DOWNLOAD = 0x06,
CMD_PIO_UPLOAD = 0x07,
CMD_RECEIVE_PACKET = 0x08,
CMD_TRANSMIT_PACKET = 0x09,
CMD_NETWORK_STATISTICS = 0x0a,
CMD_LOAD_MULTICAST_LIST = 0x0b,
CMD_CLEAR_PROGRAM = 0x0c,
CMD_DOWNLOAD_PROGRAM = 0x0d,
CMD_EXECUTE_PROGRAM = 0x0e,
CMD_SELF_TEST = 0x0f,
CMD_SET_STATION_ADDRESS = 0x10,
CMD_ADAPTER_INFO = 0x11,
NUM_TRANSMIT_CMDS,
/*
* adapter PCB commands
*/
CMD_CONFIGURE_ADAPTER_RESPONSE = 0x31,
CMD_CONFIGURE_82586_RESPONSE = 0x32,
CMD_ADDRESS_RESPONSE = 0x33,
CMD_DOWNLOAD_DATA_REQUEST = 0x34,
CMD_UPLOAD_DATA_REQUEST = 0x35,
CMD_RECEIVE_PACKET_COMPLETE = 0x38,
CMD_TRANSMIT_PACKET_COMPLETE = 0x39,
CMD_NETWORK_STATISTICS_RESPONSE = 0x3a,
CMD_LOAD_MULTICAST_RESPONSE = 0x3b,
CMD_CLEAR_PROGRAM_RESPONSE = 0x3c,
CMD_DOWNLOAD_PROGRAM_RESPONSE = 0x3d,
CMD_EXECUTE_RESPONSE = 0x3e,
CMD_SELF_TEST_RESPONSE = 0x3f,
CMD_SET_ADDRESS_RESPONSE = 0x40,
CMD_ADAPTER_INFO_RESPONSE = 0x41
};
/* Definitions for the PCB data structure */
/* Data units */
typedef unsigned char byte;
typedef unsigned short int word;
typedef unsigned long int dword;
/* Data structures */
struct Memconf {
word cmd_q,
rcv_q,
mcast,
frame,
rcv_b,
progs;
};
struct Rcv_pkt {
word buf_ofs,
buf_seg,
buf_len,
timeout;
};
struct Xmit_pkt {
word buf_ofs,
buf_seg,
pkt_len;
};
struct Rcv_resp {
word buf_ofs,
buf_seg,
buf_len,
pkt_len,
timeout,
status;
dword timetag;
};
struct Xmit_resp {
word buf_ofs,
buf_seg,
c_stat,
status;
};
struct Netstat {
dword tot_recv,
tot_xmit;
word err_CRC,
err_align,
err_res,
err_ovrrun;
};
struct Selftest {
word error;
union {
word ROM_cksum;
struct {
word ofs, seg;
} RAM;
word i82586;
} failure;
};
struct Info {
byte minor_vers,
major_vers;
word ROM_cksum,
RAM_sz,
free_ofs,
free_seg;
};
struct Memdump {
word size,
off,
seg;
};
/*
Primary Command Block. The most important data structure. All communication
between the host and the adapter is done with these. (Except for the actual
ethernet data, which has different packaging.)
*/
typedef struct {
byte command;
byte length;
union {
struct Memconf memconf;
word configure;
struct Rcv_pkt rcv_pkt;
struct Xmit_pkt xmit_pkt;
byte multicast[10][6];
byte eth_addr[6];
byte failed;
struct Rcv_resp rcv_resp;
struct Xmit_resp xmit_resp;
struct Netstat netstat;
struct Selftest selftest;
struct Info info;
struct Memdump memdump;
byte raw[62];
} data;
} pcb_struct;
/* These defines for 'configure' */
#define RECV_STATION 0x00
#define RECV_BROAD 0x01
#define RECV_MULTI 0x02
#define RECV_PROMISC 0x04
#define NO_LOOPBACK 0x00
#define INT_LOOPBACK 0x08
#define EXT_LOOPBACK 0x10
|
