summaryrefslogtreecommitdiff
path: root/i386/i386at/gpl/linux/scsi/pas16.c
diff options
context:
space:
mode:
Diffstat (limited to 'i386/i386at/gpl/linux/scsi/pas16.c')
-rw-r--r--i386/i386at/gpl/linux/scsi/pas16.c553
1 files changed, 0 insertions, 553 deletions
diff --git a/i386/i386at/gpl/linux/scsi/pas16.c b/i386/i386at/gpl/linux/scsi/pas16.c
deleted file mode 100644
index 9f5d882..0000000
--- a/i386/i386at/gpl/linux/scsi/pas16.c
+++ /dev/null
@@ -1,553 +0,0 @@
-#define AUTOSENSE
-#define PSEUDO_DMA
-#define FOO
-#define UNSAFE /* Not unsafe for PAS16 -- use it */
-
-/*
- * This driver adapted from Drew Eckhardt's Trantor T128 driver
- *
- * Copyright 1993, Drew Eckhardt
- * Visionary Computing
- * (Unix and Linux consulting and custom programming)
- * drew@colorado.edu
- * +1 (303) 666-5836
- *
- * ( Based on T128 - DISTRIBUTION RELEASE 3. )
- *
- * Modified to work with the Pro Audio Spectrum/Studio 16
- * by John Weidman.
- *
- *
- * For more information, please consult
- *
- * Media Vision
- * (510) 770-8600
- * (800) 348-7116
- *
- * and
- *
- * NCR 5380 Family
- * SCSI Protocol Controller
- * Databook
- *
- * NCR Microelectronics
- * 1635 Aeroplaza Drive
- * Colorado Springs, CO 80916
- * 1+ (719) 578-3400
- * 1+ (800) 334-5454
- */
-
-/*
- * Options :
- * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
- * for commands that return with a CHECK CONDITION status.
- *
- * LIMIT_TRANSFERSIZE - if defined, limit the pseudo-dma transfers to 512
- * bytes at a time. Since interrupts are disabled by default during
- * these transfers, we might need this to give reasonable interrupt
- * service time if the transfer size gets too large.
- *
- * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
- * increase compared to polled I/O.
- *
- * PARITY - enable parity checking. Not supported.
- *
- * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
- *
- * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. This
- * parameter comes from the NCR5380 code. It is NOT unsafe with
- * the PAS16 and you should use it. If you don't you will have
- * a problem with dropped characters during high speed
- * communications during SCSI transfers. If you really don't
- * want to use UNSAFE you can try defining LIMIT_TRANSFERSIZE or
- * twiddle with the transfer size in the high level code.
- *
- * USLEEP - enable support for devices that don't disconnect. Untested.
- *
- * The card is detected and initialized in one of several ways :
- * 1. Autoprobe (default) - There are many different models of
- * the Pro Audio Spectrum/Studio 16, and I only have one of
- * them, so this may require a little tweaking. An interrupt
- * is triggered to autoprobe for the interrupt line. Note:
- * with the newer model boards, the interrupt is set via
- * software after reset using the default_irq for the
- * current board number.
- *
- *
- * 2. With command line overrides - pas16=port,irq may be
- * used on the LILO command line to override the defaults.
- *
- * 3. With the PAS16_OVERRIDE compile time define. This is
- * specified as an array of address, irq tuples. Ie, for
- * one board at the default 0x388 address, IRQ10, I could say
- * -DPAS16_OVERRIDE={{0x388, 10}}
- * NOTE: Untested.
- *
- * Note that if the override methods are used, place holders must
- * be specified for other boards in the system.
- *
- *
- * Configuration notes :
- * The current driver does not support interrupt sharing with the
- * sound portion of the card. If you use the same irq for the
- * scsi port and sound you will have problems. Either use
- * a different irq for the scsi port or don't use interrupts
- * for the scsi port.
- *
- * If you have problems with your card not being recognized, use
- * the LILO command line override. Try to get it recognized without
- * interrupts. Ie, for a board at the default 0x388 base port,
- * boot: linux pas16=0x388,255
- *
- * (255 is the IRQ_NONE constant in NCR5380.h)
- */
-
-#ifdef MODULE
-#include <linux/module.h>
-#endif
-
-#include <asm/system.h>
-#include <linux/signal.h>
-#include <linux/proc_fs.h>
-#include <linux/sched.h>
-#include <asm/io.h>
-#include <linux/blk.h>
-#include "scsi.h"
-#include "hosts.h"
-#include "pas16.h"
-#define AUTOPROBE_IRQ
-#include "NCR5380.h"
-#include "constants.h"
-#include "sd.h"
-
-#include<linux/stat.h>
-
-struct proc_dir_entry proc_scsi_pas16 = {
- PROC_SCSI_PAS16, 5, "pas16",
- S_IFDIR | S_IRUGO | S_IXUGO, 2
-};
-
-int scsi_irq_translate[] =
- { 0, 0, 1, 2, 3, 4, 5, 6, 0, 0, 7, 8, 9, 0, 10, 11 };
-
-/* The default_irqs array contains values used to set the irq into the
- * board via software (as must be done on newer model boards without
- * irq jumpers on the board). The first value in the array will be
- * assigned to logical board 0, the next to board 1, etc.
- */
-int default_irqs[] = { PAS16_DEFAULT_BOARD_1_IRQ,
- PAS16_DEFAULT_BOARD_2_IRQ,
- PAS16_DEFAULT_BOARD_3_IRQ,
- PAS16_DEFAULT_BOARD_4_IRQ
- };
-
-static struct override {
- unsigned short io_port;
- int irq;
-} overrides
-#ifdef PAS16_OVERRIDE
- [] = PAS16_OVERRIDE;
-#else
- [4] = {{0,IRQ_AUTO}, {0,IRQ_AUTO}, {0,IRQ_AUTO},
- {0,IRQ_AUTO}};
-#endif
-
-#define NO_OVERRIDES (sizeof(overrides) / sizeof(struct override))
-
-static struct base {
- unsigned short io_port;
- int noauto;
-} bases[] = { {PAS16_DEFAULT_BASE_1, 0},
- {PAS16_DEFAULT_BASE_2, 0},
- {PAS16_DEFAULT_BASE_3, 0},
- {PAS16_DEFAULT_BASE_4, 0}
- };
-
-#define NO_BASES (sizeof (bases) / sizeof (struct base))
-
-unsigned short pas16_offset[ 8 ] =
- {
- 0x1c00, /* OUTPUT_DATA_REG */
- 0x1c01, /* INITIATOR_COMMAND_REG */
- 0x1c02, /* MODE_REG */
- 0x1c03, /* TARGET_COMMAND_REG */
- 0x3c00, /* STATUS_REG ro, SELECT_ENABLE_REG wo */
- 0x3c01, /* BUS_AND_STATUS_REG ro, START_DMA_SEND_REG wo */
- 0x3c02, /* INPUT_DATA_REGISTER ro, (N/A on PAS16 ?)
- * START_DMA_TARGET_RECEIVE_REG wo
- */
- 0x3c03, /* RESET_PARITY_INTERRUPT_REG ro,
- * START_DMA_INITIATOR_RECEIVE_REG wo
- */
- };
-
-
-
-/*
- * Function : enable_board( int board_num, unsigned short port )
- *
- * Purpose : set address in new model board
- *
- * Inputs : board_num - logical board number 0-3, port - base address
- *
- */
-
-void enable_board( int board_num, unsigned short port )
-{
- outb( 0xbc + board_num, MASTER_ADDRESS_PTR );
- outb( port >> 2, MASTER_ADDRESS_PTR );
-}
-
-
-
-/*
- * Function : init_board( unsigned short port, int irq )
- *
- * Purpose : Set the board up to handle the SCSI interface
- *
- * Inputs : port - base address of the board,
- * irq - irq to assign to the SCSI port
- * force_irq - set it even if it conflicts with sound driver
- *
- */
-
-void init_board( unsigned short io_port, int irq, int force_irq )
-{
- unsigned int tmp;
- unsigned int pas_irq_code;
-
- /* Initialize the SCSI part of the board */
-
- outb( 0x30, io_port + P_TIMEOUT_COUNTER_REG ); /* Timeout counter */
- outb( 0x01, io_port + P_TIMEOUT_STATUS_REG_OFFSET ); /* Reset TC */
- outb( 0x01, io_port + WAIT_STATE ); /* 1 Wait state */
-
- NCR5380_read( RESET_PARITY_INTERRUPT_REG );
-
- /* Set the SCSI interrupt pointer without mucking up the sound
- * interrupt pointer in the same byte.
- */
- pas_irq_code = ( irq < 16 ) ? scsi_irq_translate[irq] : 0;
- tmp = inb( io_port + IO_CONFIG_3 );
-
- if( (( tmp & 0x0f ) == pas_irq_code) && pas_irq_code > 0
- && !force_irq )
- {
- printk( "pas16: WARNING: Can't use same irq as sound "
- "driver -- interrupts disabled\n" );
- /* Set up the drive parameters, disable 5380 interrupts */
- outb( 0x4d, io_port + SYS_CONFIG_4 );
- }
- else
- {
- tmp = ( tmp & 0x0f ) | ( pas_irq_code << 4 );
- outb( tmp, io_port + IO_CONFIG_3 );
-
- /* Set up the drive parameters and enable 5380 interrupts */
- outb( 0x6d, io_port + SYS_CONFIG_4 );
- }
-}
-
-
-/*
- * Function : pas16_hw_detect( unsigned short board_num )
- *
- * Purpose : determine if a pas16 board is present
- *
- * Inputs : board_num - logical board number ( 0 - 3 )
- *
- * Returns : 0 if board not found, 1 if found.
- */
-
-int pas16_hw_detect( unsigned short board_num )
-{
- unsigned char board_rev, tmp;
- unsigned short io_port = bases[ board_num ].io_port;
-
- /* See if we can find a PAS16 board at the address associated
- * with this logical board number.
- */
-
- /* First, attempt to take a newer model board out of reset and
- * give it a base address. This shouldn't affect older boards.
- */
- enable_board( board_num, io_port );
-
- /* Now see if it looks like a PAS16 board */
- board_rev = inb( io_port + PCB_CONFIG );
-
- if( board_rev == 0xff )
- return 0;
-
- tmp = board_rev ^ 0xe0;
-
- outb( tmp, io_port + PCB_CONFIG );
- tmp = inb( io_port + PCB_CONFIG );
- outb( board_rev, io_port + PCB_CONFIG );
-
- if( board_rev != tmp ) /* Not a PAS-16 */
- return 0;
-
- if( ( inb( io_port + OPERATION_MODE_1 ) & 0x03 ) != 0x03 )
- return 0; /* return if no SCSI interface found */
-
- /* Mediavision has some new model boards that return ID bits
- * that indicate a SCSI interface, but they're not (LMS). We'll
- * put in an additional test to try and weed them out.
- */
-
- outb( 0x01, io_port + WAIT_STATE ); /* 1 Wait state */
- NCR5380_write( MODE_REG, 0x20 ); /* Is it really SCSI? */
- if( NCR5380_read( MODE_REG ) != 0x20 ) /* Write to a reg. */
- return 0; /* and try to read */
- NCR5380_write( MODE_REG, 0x00 ); /* it back. */
- if( NCR5380_read( MODE_REG ) != 0x00 )
- return 0;
-
- return 1;
-}
-
-
-/*
- * Function : pas16_setup(char *str, int *ints)
- *
- * Purpose : LILO command line initialization of the overrides array,
- *
- * Inputs : str - unused, ints - array of integer parameters with ints[0]
- * equal to the number of ints.
- *
- */
-
-void pas16_setup(char *str, int *ints) {
- static int commandline_current = 0;
- int i;
- if (ints[0] != 2)
- printk("pas16_setup : usage pas16=io_port,irq\n");
- else
- if (commandline_current < NO_OVERRIDES) {
- overrides[commandline_current].io_port = (unsigned short) ints[1];
- overrides[commandline_current].irq = ints[2];
- for (i = 0; i < NO_BASES; ++i)
- if (bases[i].io_port == (unsigned short) ints[1]) {
- bases[i].noauto = 1;
- break;
- }
- ++commandline_current;
- }
-}
-
-/*
- * Function : int pas16_detect(Scsi_Host_Template * tpnt)
- *
- * Purpose : detects and initializes PAS16 controllers
- * that were autoprobed, overridden on the LILO command line,
- * or specified at compile time.
- *
- * Inputs : tpnt - template for this SCSI adapter.
- *
- * Returns : 1 if a host adapter was found, 0 if not.
- *
- */
-
-int pas16_detect(Scsi_Host_Template * tpnt) {
- static int current_override = 0;
- static unsigned short current_base = 0;
- struct Scsi_Host *instance;
- unsigned short io_port;
- int count;
-
- tpnt->proc_dir = &proc_scsi_pas16;
-
- for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
- io_port = 0;
-
- if (overrides[current_override].io_port)
- {
- io_port = overrides[current_override].io_port;
- enable_board( current_override, io_port );
- init_board( io_port, overrides[current_override].irq, 1 );
- }
- else
- for (; !io_port && (current_base < NO_BASES); ++current_base) {
-#if (PDEBUG & PDEBUG_INIT)
- printk("scsi-pas16 : probing io_port %04x\n", (unsigned int) bases[current_base].io_port);
-#endif
- if ( !bases[current_base].noauto &&
- pas16_hw_detect( current_base ) ){
- io_port = bases[current_base].io_port;
- init_board( io_port, default_irqs[ current_base ], 0 );
-#if (PDEBUG & PDEBUG_INIT)
- printk("scsi-pas16 : detected board.\n");
-#endif
- }
- }
-
-
-#if defined(PDEBUG) && (PDEBUG & PDEBUG_INIT)
- printk("scsi-pas16 : io_port = %04x\n", (unsigned int) io_port);
-#endif
-
- if (!io_port)
- break;
-
- instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
- instance->io_port = io_port;
-
- NCR5380_init(instance, 0);
-
- if (overrides[current_override].irq != IRQ_AUTO)
- instance->irq = overrides[current_override].irq;
- else
- instance->irq = NCR5380_probe_irq(instance, PAS16_IRQS);
-
- if (instance->irq != IRQ_NONE)
- if (request_irq(instance->irq, pas16_intr, SA_INTERRUPT, "pas16")) {
- printk("scsi%d : IRQ%d not free, interrupts disabled\n",
- instance->host_no, instance->irq);
- instance->irq = IRQ_NONE;
- }
-
- if (instance->irq == IRQ_NONE) {
- printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
- printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
- /* Disable 5380 interrupts, leave drive params the same */
- outb( 0x4d, io_port + SYS_CONFIG_4 );
- outb( (inb(io_port + IO_CONFIG_3) & 0x0f), io_port + IO_CONFIG_3 );
- }
-
-#if defined(PDEBUG) && (PDEBUG & PDEBUG_INIT)
- printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
-#endif
-
- printk("scsi%d : at 0x%04x", instance->host_no, (int)
- instance->io_port);
- if (instance->irq == IRQ_NONE)
- printk (" interrupts disabled");
- else
- printk (" irq %d", instance->irq);
- printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
- CAN_QUEUE, CMD_PER_LUN, PAS16_PUBLIC_RELEASE);
- NCR5380_print_options(instance);
- printk("\n");
-
- ++current_override;
- ++count;
- }
- return count;
-}
-
-/*
- * Function : int pas16_biosparam(Disk *disk, kdev_t dev, int *ip)
- *
- * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
- * the specified device / size.
- *
- * Inputs : size = size of device in sectors (512 bytes), dev = block device
- * major / minor, ip[] = {heads, sectors, cylinders}
- *
- * Returns : always 0 (success), initializes ip
- *
- */
-
-/*
- * XXX Most SCSI boards use this mapping, I could be incorrect. Some one
- * using hard disks on a trantor should verify that this mapping corresponds
- * to that used by the BIOS / ASPI driver by running the linux fdisk program
- * and matching the H_C_S coordinates to what DOS uses.
- */
-
-int pas16_biosparam(Disk * disk, kdev_t dev, int * ip)
-{
- int size = disk->capacity;
- ip[0] = 64;
- ip[1] = 32;
- ip[2] = size >> 11; /* I think I have it as /(32*64) */
- if( ip[2] > 1024 ) { /* yes, >, not >= */
- ip[0]=255;
- ip[1]=63;
- ip[2]=size/(63*255);
- if( ip[2] > 1023 ) /* yes >1023... */
- ip[2] = 1023;
- }
-
- return 0;
-}
-
-/*
- * Function : int NCR5380_pread (struct Scsi_Host *instance,
- * unsigned char *dst, int len)
- *
- * Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to
- * dst
- *
- * Inputs : dst = destination, len = length in bytes
- *
- * Returns : 0 on success, non zero on a failure such as a watchdog
- * timeout.
- */
-
-static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,
- int len) {
- register unsigned char *d = dst;
- register unsigned short reg = (unsigned short) (instance->io_port +
- P_DATA_REG_OFFSET);
- register i = len;
-
- while ( !(inb(instance->io_port + P_STATUS_REG_OFFSET) & P_ST_RDY) );
-
- insb( reg, d, i );
-
- if ( inb(instance->io_port + P_TIMEOUT_STATUS_REG_OFFSET) & P_TS_TIM) {
- outb( P_TS_CT, instance->io_port + P_TIMEOUT_STATUS_REG_OFFSET);
- printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
- instance->host_no);
- return -1;
- } else
- return 0;
-}
-
-/*
- * Function : int NCR5380_pwrite (struct Scsi_Host *instance,
- * unsigned char *src, int len)
- *
- * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
- * src
- *
- * Inputs : src = source, len = length in bytes
- *
- * Returns : 0 on success, non zero on a failure such as a watchdog
- * timeout.
- */
-
-static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,
- int len) {
- register unsigned char *s = src;
- register unsigned short reg = (instance->io_port + P_DATA_REG_OFFSET);
- register i = len;
-
- while ( !((inb(instance->io_port + P_STATUS_REG_OFFSET)) & P_ST_RDY) );
-
- outsb( reg, s, i );
-
- if (inb(instance->io_port + P_TIMEOUT_STATUS_REG_OFFSET) & P_TS_TIM) {
- outb( P_TS_CT, instance->io_port + P_TIMEOUT_STATUS_REG_OFFSET);
- printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
- instance->host_no);
- return -1;
- } else
- return 0;
-}
-
-#ifdef MACH
-#include "NCR5380.src"
-#else
-#include "NCR5380.c"
-#endif
-
-#ifdef MODULE
-/* Eventually this will go into an include file, but this will be later */
-Scsi_Host_Template driver_template = MV_PAS16;
-
-#include <linux/module.h>
-#include "scsi_module.c"
-#endif
generated by cgit v1.2.3 (git 2.46.0) at 2025-04-05 14:00:11 +0000