1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
|
[[meta copyright="Copyright © 2007, 2008 Free Software Foundation, Inc."]]
[[meta license="""[[toggle id="license" text="GFDL 1.2+"]][[toggleable
id="license" text="Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU Free Documentation License, Version 1.2 or
any later version published by the Free Software Foundation; with no Invariant
Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license
is included in the section entitled
[[GNU_Free_Documentation_License|/fdl]]."]]"""]]
[[toc ]]
## Xen dom0, hypervisor
/!\ Now that GNU Mach handles PAE you can use a PAE-enabled hypervisor.
You can either get binaries at <http://youpibouh.thefreecat.org/hurd-xen/> or build them yourself.
- Copy `gnumach-xen` and `hurd-modules` to your dom0 /boot.
- Copy `hurd` into `/etc/xen`, edit it for fixing access to your hurd / and swap
## GNU/Hurd system
/!\ You need an already installed GNU/Hurd system.
If you have a free partition, you can fdisk to type 0x83, create a filesystem using:
sudo mke2fs -b 4096 -I 128 -o hurd /dev/sda4
Replace /dev/sda4 with your partition. Install and use crosshurd to setup a GNU/Hurd system on this partition.
## /etc/xen/hurd configuration
Here is a sample /etc/xen/hurd configuration
kernel = "/boot/gnumach-xen"
memory = 256
disk = ['phy:sda4,hda,w']
extra = "root=device:hd0"
vif = [ '' ]
ramdisk = "/boot/hurd-modules"
Suggestions about [[networking_configuration]] are available.
If you need stable MAC addresses, use a syntax like `vif = [
'mac=00:16:3e:XX:XX:XX, bridge=br0' ]`.
## Running Hurd with Xen
To run Hurd with Xen, use:
xm create -c hurd
and gnumach should get started. Proceed with native-install.
export TERM=mach
./native-install
- If `xm` complains about networking (`vif could not be connected`), it's Xen scripts' fault, see Xen documentation for how to configure the network. The simplest way is network-bridge with fixed IPs (note that you need the bridge-utils package for this). You can also just disable networking by commenting the vif line in the config.
- If `xm` complains `Error: (2, 'Invalid kernel', 'xc_dom_compat_check: guest type xen-3.0-x86_32 not supported by xen kernel, sorry\n')`, you most probably have a PAE-enabled hypervisor and a non-PAE gnumach. Either install and boot non-PAE hypervisor and kernel, or rebuilt gnumach in PAE mode.
## Building from sources
If you want to generate these images, first get the `gnumach-1-branch-Xen-branch` branch from gnumach CVS.
Then look for "Ugly" in `kern/bootstrap.c`, how to generate `hurd-modules` is explained there, and you'll have to fix `EXT2FS_SIZE` and `LD_SO_SIZE` by hand.
Then use
./configure --enable-platform=xen
make
The current `hurd-modules` was built from the debian packages `hurd 20070606-2` and `libc0.3 2.6.1-1`.
/!\ This means that when using this image, your GNU/Hurd system also needs to be a glibc version 2.6-based one!
---
[[Internals]].
[[GNU_Savannah_task 5468]], [[GNU_Savannah_task 6584]].
|
