diff options
| -rw-r--r-- | Mach/BuildingOskitMach.mdwn | 22 |
1 files changed, 16 insertions, 6 deletions
diff --git a/Mach/BuildingOskitMach.mdwn b/Mach/BuildingOskitMach.mdwn index 0fc5e851..dedc8c1f 100644 --- a/Mach/BuildingOskitMach.mdwn +++ b/Mach/BuildingOskitMach.mdwn @@ -4,6 +4,8 @@ This is a brief Building OSKit Mach HowTO. It covers everything from getting the latest sources of both the [OSKit](http://www.cs.utah.edu/flux/oskit/) and the OSKit branch of the GNUmach kernel. There is also [another guide](http://www.etherhogz.org/doc/oskit-mach.html). Down to building and debugging them. On May 27 after the [[GnuMach]] 1.3 release, Roland McGrath merged OSKit Mach in the [[GnuMach]] 2.x mainline. +To be able to actually make use of your recently checked out CVS version of the GNUMach kernel & C:o you need a GNU system of [gnu-20020816.tar.gz](ftp://ftp.funet.fi/pub/gnu/alpha/gnu/hurd/contrib/marcus/gnu-20020816.tar.gz) or later. + ## <a name="Getting_your_hands_on_the_source"> Getting your hands on the source </a> First you need to checkout the relevant sources. @@ -34,14 +36,15 @@ This is only a brief restatement, which may ormay not be accurate. Setup your en All development, apart from critical bug fixes, is done on the upcoming 2.0 release. Previously the oskit-branch of gnumach. - cvs -z3 co -d gnumach - -_did you mean cvs -z3 co gnumach ?_ + cvs -z3 co gnumach In case you have been tracking the oskit-branch and want to move to the current HEAD branch you can issue the following instead to update your tree. + cd <YOUR MACH DIR> cvs -z3 update -r HEAD -Pd +Where <YOUR MACH DIR> can be gnumach, oskit-mach, or similar. + **_The Hurd servers:_** In case you want to build the Hurd servers as well, you can check them out too: @@ -60,14 +63,14 @@ Check it out using ### <a name="The_OSKit"> </a> The OSKit -The attached [[ATTACHURLmodulesx86pc]] file is my personal setup, it works for me. Now, how to configure and build the OSKit. +The attached [[ATTACHURLmodulesx86pc]] is an example setup, your needs may vary but this one works for standard COTS PC's. Now, how to configure and build the OSKit. **_Configuring:_** # cd oskit-20020317/ # mkdir build # cd build - # ../configure --prefix=/usr/local --enable-debug + # CFLAGS="-g" ../configure --prefix=/usr/local --enable-debug **_Building:_** @@ -91,10 +94,17 @@ This will install the i386-gnu-mig in /usr/bin for you. **_Building:_** - # make + # make kernel-ide+ethernet_vortex # sudo make install # sudo gzip /gnu/boot/oskit-mach +Instead of using \`make kernel' to build kernel, in OSKit-Mach you have to use \`make kernel-DRIVERS', where DRIVERS is \`DRIVER+DRIVER+...+DRIVER' (a list of drivers separated by \`+'). DRIVER can be one of: + +* \`ide' +* \`floppy' +* \`ethernet\_ETHDRV' where ETHDRV is taken from 'oskit/oskit/dev/linux\_ethernet.h'. +* \`scsi\_SCSIDRV' where SCSIDRV is taken from \`oskit/oskit/dev/linux\_scsi.h'. + ## <a name="Debugging"> Debugging </a> For now, see the [[RemoteDebugOskitMach]] page. |