diff options
Diffstat (limited to 'linux/src/drivers/net/eth82586.h')
-rw-r--r-- | linux/src/drivers/net/eth82586.h | 172 |
1 files changed, 172 insertions, 0 deletions
diff --git a/linux/src/drivers/net/eth82586.h b/linux/src/drivers/net/eth82586.h new file mode 100644 index 0000000..c2178ff --- /dev/null +++ b/linux/src/drivers/net/eth82586.h @@ -0,0 +1,172 @@ +/* + * eth82586.h: Intel EtherExpress defines + * + * Written 1995 by John Sullivan + * See eexpress.c for further details + * documentation and usage to do. + */ + +/* + * EtherExpress card register addresses + * as offsets from the base IO region (dev->base_addr) + */ + +#define DATAPORT 0x0000 +#define WRITE_PTR 0x0002 +#define READ_PTR 0x0004 +#define SIGNAL_CA 0x0006 +#define SET_IRQ 0x0007 +#define SM_PTR 0x0008 +#define MEM_Ctrl 0x000b +#define MEM_Page_Ctrl 0x000c +#define Config 0x000d +#define EEPROM_Ctrl 0x000e +#define ID_PORT 0x000f + +/* + * offset to shadowed memory, 0 <= x <= 31. We don't use this yet, + * but may in the future. Is shadow memory access any faster than + * dataport access? + */ +#define SM_ADDR(x) (0x4000+((x&0x10)<<10)+(x&0xf)) + +/* Always mirrors eexp-memory at 0x0008-0x000f */ +#define SCB_STATUS 0xc008 +#define SCB_CMD 0xc00a +#define SCB_CBL 0xc00c +#define SCB_RFA 0xc00e + + + +/* + * card register defines + */ + +/* SET_IRQ */ +#define SIRQ_en 0x08 +#define SIRQ_dis 0x00 + +/* Config */ +#define set_loopback outb(inb(ioaddr+Config)|0x02,ioaddr+Config) +#define clear_loopback outb(inb(ioaddr+Config)&0xfd,ioaddr+Config) + +/* EEPROM_Ctrl */ +#define EC_Clk 0x01 +#define EC_CS 0x02 +#define EC_Wr 0x04 +#define EC_Rd 0x08 +#define ASIC_RST 0x40 +#define i586_RST 0x80 + +#define eeprom_delay() { int _i = 40; while (--_i>0) { __SLOW_DOWN_IO; }} + +/* + * i82586 Memory Configuration + */ + +/* (System Configuration Pointer) System start up block, read after 586_RST */ +#define SCP_START 0xfff6 + + +/* Intermediate System Configuration Pointer */ +#define ISCP_START 0x0000 +/* System Command Block */ +#define SCB_START 0x0008 + +/* + * Start of buffer region. If we have 64k memory, eexp_hw_probe() may raise + * NUM_TX_BUFS. RX_BUF_END is set to the end of memory, and all space between + * the transmit buffer region and end of memory used for as many receive buffers + * as we can fit. See eexp_hw_[(rx)(tx)]init(). + */ +#define TX_BUF_START 0x0100 +#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f) +#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f) + + + +/* + * SCB defines + */ + +/* these functions take the SCB status word and test the relevant status bit */ +#define SCB_complete(s) ((s&0x8000)!=0) +#define SCB_rxdframe(s) ((s&0x4000)!=0) +#define SCB_CUdead(s) ((s&0x2000)!=0) +#define SCB_RUdead(s) ((s&0x1000)!=0) +#define SCB_ack(s) (s & 0xf000) + +/* Command unit status: 0=idle, 1=suspended, 2=active */ +#define SCB_CUstat(s) ((s&0x0300)>>8) + +/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */ +#define SCB_RUstat(s) ((s&0x0070)>>4) + +/* SCB commands */ +#define SCB_CUnop 0x0000 +#define SCB_CUstart 0x0100 +#define SCB_CUresume 0x0200 +#define SCB_CUsuspend 0x0300 +#define SCB_CUabort 0x0400 + +/* ? */ +#define SCB_resetchip 0x0080 + +#define SCB_RUnop 0x0000 +#define SCB_RUstart 0x0010 +#define SCB_RUresume 0x0020 +#define SCB_RUsuspend 0x0030 +#define SCB_RUabort 0x0040 + + +/* + * Command block defines + */ + +#define Stat_Done(s) ((s&0x8000)!=0) +#define Stat_Busy(s) ((s&0x4000)!=0) +#define Stat_OK(s) ((s&0x2000)!=0) +#define Stat_Abort(s) ((s&0x1000)!=0) +#define Stat_STFail ((s&0x0800)!=0) +#define Stat_TNoCar(s) ((s&0x0400)!=0) +#define Stat_TNoCTS(s) ((s&0x0200)!=0) +#define Stat_TNoDMA(s) ((s&0x0100)!=0) +#define Stat_TDefer(s) ((s&0x0080)!=0) +#define Stat_TColl(s) ((s&0x0040)!=0) +#define Stat_TXColl(s) ((s&0x0020)!=0) +#define Stat_NoColl(s) (s&0x000f) + +/* Cmd_END will end AFTER the command if this is the first + * command block after an SCB_CUstart, but BEFORE the command + * for all subsequent commands. Best strategy is to place + * Cmd_INT on the last command in the sequence, followed by a + * dummy Cmd_Nop with Cmd_END after this. + */ +#define Cmd_END 0x8000 +#define Cmd_SUS 0x4000 +#define Cmd_INT 0x2000 + +#define Cmd_Nop 0x0000 +#define Cmd_SetAddr 0x0001 +#define Cmd_Config 0x0002 +#define Cmd_MCast 0x0003 +#define Cmd_Xmit 0x0004 +#define Cmd_TDR 0x0005 +#define Cmd_Dump 0x0006 +#define Cmd_Diag 0x0007 + + +/* + * Frame Descriptor (Receive block) defines + */ + +#define FD_Done(s) ((s&0x8000)!=0) +#define FD_Busy(s) ((s&0x4000)!=0) +#define FD_OK(s) ((s&0x2000)!=0) + +#define FD_CRC(s) ((s&0x0800)!=0) +#define FD_Align(s) ((s&0x0400)!=0) +#define FD_Resrc(s) ((s&0x0200)!=0) +#define FD_DMA(s) ((s&0x0100)!=0) +#define FD_Short(s) ((s&0x0080)!=0) +#define FD_NoEOF(s) ((s&0x0040)!=0) |