1998-11-30 OKUJI Yoshinori <okuji@kuicr.kyoto-u.ac.jp>

	Clean up linux emulation code to make it architecture-independent
	as much as possible.

	* linux: Renamed from linuxdev.
	* Makefile.in (objfiles): Add linux.o instead of linuxdev.o.
	(MAKE): New variable. Used for the linux.o target.
	* configure.in: Add AC_CHECK_TOOL(MAKE, make).
	* i386/i386/spl.h: Include <i386/ipl.h>, for compatibility with
	OSF Mach 3.0. Suggested by Elgin Lee <ehl@funghi.com>.
	* linux/src: Renamed from linux/linux.
	* linux/dev: Renamed from linux/mach.
	* linux/Drivers.in (AC_INIT): Use dev/include/linux/autoconf.h,
	instead of mach/include/linux/autoconf.h.
	* Makefile.in (all): Target ../linux.o instead of ../linuxdev.o.
	* linux/dev/drivers/block/genhd.c: Include <machine/spl.h> instead
	of <i386/ipl.h>.
	* linux/dev/drivers/net/auto_irq.c: Remove unneeded header files,
	<i386/ipl.h> and <i386/pic.h>.
	* linux/dev/init/main.c: Many i386-dependent codes moved to ...
	* linux/dev/arch/i386/irq.c: ... here.
	* linux/dev/arch/i386/setup.c: New file.
	* linux/dev/arch/i386/linux_emul.h: Likewise.
	* linux/dev/arch/i386/glue/timer.c: Merged into sched.c.
	* linux/dev/arch/i386/glue/sched.c: Include <machine/spl.h> instead
	of <i386/ipl.h>, and moved to ...
	* linux/dev/kernel/sched.c: ... here.
	* linux/dev/arch/i386/glue/block.c: Include <machine/spl.h> and
	<linux_emul.h>, instead of i386-dependent header files, and
	moved to ...
	* linux/dev/glue/blocl.c: ... here.
	* linux/dev/arch/i386/glue/net.c: Include <machine/spl.h> and
	<linux_emul.h>, instead of i386-dependent header files, and
	moved to ...
	* linux/dev/glue/net.c: ... here.
	* linux/dev/arch/i386/glue/misc.c: Remove `x86' and moved to ...
	* linux/dev/glue/misc.c: ... here.
	* linux/dev/arch/i386/glue/kmem.c: Moved to ...
	* linux/dev/glue/kmem.c: ... here.

1 files changed, 2082 insertions, 0 deletions

diff --git a/linux/src/drivers/scsi/fdomain.c b/linux/src/drivers/scsi/fdomain.c
new file mode 100644
index 0000000..df71f5c
--- /dev/null
+++ b/linux/src/drivers/scsi/fdomain.c
@@ -0,0 +1,2082 @@
+/* fdomain.c -- Future Domain TMC-16x0 SCSI driver
+ * Created: Sun May  3 18:53:19 1992 by faith@cs.unc.edu
+ * Revised: Sat Nov  2 09:27:47 1996 by root@cs.unc.edu
+ * Author: Rickard E. Faith, faith@cs.unc.edu
+ * Copyright 1992, 1993, 1994, 1995, 1996 Rickard E. Faith
+ *
+ * $Id: fdomain.c,v 1.1 1999/04/26 05:54:32 tb Exp $
+
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+
+ **************************************************************************
+
+ SUMMARY:
+
+ Future Domain BIOS versions supported for autodetect:
+    2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61
+ Chips are supported:
+    TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70
+ Boards supported:
+    Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX
+    Future Domain TMC-3260 (PCI)
+    Quantum ISA-200S, ISA-250MG
+    Adaptec AHA-2920 (PCI)
+    IBM ?
+ LILO command-line options:
+    fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>]
+
+
+
+ DESCRIPTION:
+ 
+ This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680
+ TMC-1650/1670, and TMC-3260 SCSI host adapters.  The 1650 and 1670 have a
+ 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin
+ high-density external connector.  The 1670 and 1680 have floppy disk
+ controllers built in.  The TMC-3260 is a PCI bus card.
+
+ Future Domain's older boards are based on the TMC-1800 chip, and this
+ driver was originally written for a TMC-1680 board with the TMC-1800 chip.
+ More recently, boards are being produced with the TMC-18C50 and TMC-18C30
+ chips.  The latest and greatest board may not work with this driver.  If
+ you have to patch this driver so that it will recognize your board's BIOS
+ signature, then the driver may fail to function after the board is
+ detected.
+
+ Please note that the drive ordering that Future Domain implemented in BIOS
+ versions 3.4 and 3.5 is the opposite of the order (currently) used by the
+ rest of the SCSI industry.  If you have BIOS version 3.4 or 3.5, and have
+ more then one drive, then the drive ordering will be the reverse of that
+ which you see under DOS.  For example, under DOS SCSI ID 0 will be D: and
+ SCSI ID 1 will be C: (the boot device).  Under Linux, SCSI ID 0 will be
+ /dev/sda and SCSI ID 1 will be /dev/sdb.  The Linux ordering is consistent
+ with that provided by all the other SCSI drivers for Linux.  If you want
+ this changed, you will probably have to patch the higher level SCSI code.
+ If you do so, please send me patches that are protected by #ifdefs.
+
+ If you have a TMC-8xx or TMC-9xx board, then this is not the driver for
+ your board.  Please refer to the Seagate driver for more information and
+ possible support.
+
+
+ 
+ HISTORY:
+
+ Linux       Driver      Driver
+ Version     Version     Date         Support/Notes
+
+             0.0          3 May 1992  V2.0 BIOS; 1800 chip
+ 0.97        1.9         28 Jul 1992
+ 0.98.6      3.1         27 Nov 1992
+ 0.99        3.2          9 Dec 1992
+
+ 0.99.3      3.3         10 Jan 1993  V3.0 BIOS
+ 0.99.5      3.5         18 Feb 1993
+ 0.99.10     3.6         15 May 1993  V3.2 BIOS; 18C50 chip
+ 0.99.11     3.17         3 Jul 1993  (now under RCS)
+ 0.99.12     3.18        13 Aug 1993
+ 0.99.14     5.6         31 Oct 1993  (reselection code removed)
+
+ 0.99.15     5.9         23 Jan 1994  V3.4 BIOS (preliminary)
+ 1.0.8/1.1.1 5.15         1 Apr 1994  V3.4 BIOS; 18C30 chip (preliminary)
+ 1.0.9/1.1.3 5.16         7 Apr 1994  V3.4 BIOS; 18C30 chip
+ 1.1.38      5.18        30 Jul 1994  36C70 chip (PCI version of 18C30)
+ 1.1.62      5.20         2 Nov 1994  V3.5 BIOS
+ 1.1.73      5.22         7 Dec 1994  Quantum ISA-200S board; V2.0 BIOS
+
+ 1.1.82      5.26        14 Jan 1995  V3.5 BIOS; TMC-1610M/MER/MEX board
+ 1.2.10      5.28         5 Jun 1995  Quantum ISA-250MG board; V2.0, V2.01 BIOS
+ 1.3.4       5.31        23 Jun 1995  PCI BIOS-32 detection (preliminary)
+ 1.3.7       5.33         4 Jul 1995  PCI BIOS-32 detection
+ 1.3.28      5.36        17 Sep 1995  V3.61 BIOS; LILO command-line support
+ 1.3.34      5.39        12 Oct 1995  V3.60 BIOS; /proc
+ 1.3.72      5.39         8 Feb 1996  Adaptec AHA-2920 board
+ 1.3.85      5.41         4 Apr 1996
+ 2.0.12      5.44         8 Aug 1996  Use ID 7 for all PCI cards
+
+ 
+
+ REFERENCES USED:
+
+ "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation,
+ 1990.
+
+ "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain
+ Corporation, January 1992.
+
+ "LXT SCSI Products: Specifications and OEM Technical Manual (Revision
+ B/September 1991)", Maxtor Corporation, 1991.
+
+ "7213S product Manual (Revision P3)", Maxtor Corporation, 1992.
+
+ "Draft Proposed American National Standard: Small Computer System
+ Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109,
+ revision 10h, October 17, 1991)
+
+ Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric
+ Youngdale (ericy@cais.com), 1992.
+
+ Private communication, Tuong Le (Future Domain Engineering department),
+ 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and
+ TMC-18C30 detection.)
+
+ Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page
+ 60 (2.39: Disk Partition Table Layout).
+
+ "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page
+ 6-1.
+
+
+ 
+ NOTES ON REFERENCES:
+
+ The Maxtor manuals were free.  Maxtor telephone technical support is
+ great!
+
+ The Future Domain manuals were $25 and $35.  They document the chip, not
+ the TMC-16x0 boards, so some information I had to guess at.  In 1992,
+ Future Domain sold DOS BIOS source for $250 and the UN*X driver source was
+ $750, but these required a non-disclosure agreement, so even if I could
+ have afforded them, they would *not* have been useful for writing this
+ publically distributable driver.  Future Domain technical support has
+ provided some information on the phone and have sent a few useful FAXs.
+ They have been much more helpful since they started to recognize that the
+ word "Linux" refers to an operating system :-).
+
+ 
+
+ ALPHA TESTERS:
+
+ There are many other alpha testers that come and go as the driver
+ develops.  The people listed here were most helpful in times of greatest
+ need (mostly early on -- I've probably left out a few worthy people in
+ more recent times):
+
+ Todd Carrico (todd@wutc.wustl.edu), Dan Poirier (poirier@cs.unc.edu ), Ken
+ Corey (kenc@sol.acs.unt.edu), C. de Bruin (bruin@bruin@sterbbs.nl), Sakari
+ Aaltonen (sakaria@vipunen.hit.fi), John Rice (rice@xanth.cs.odu.edu), Brad
+ Yearwood (brad@optilink.com), and Ray Toy (toy@soho.crd.ge.com).
+
+ Special thanks to Tien-Wan Yang (twyang@cs.uh.edu), who graciously lent me
+ his 18C50-based card for debugging.  He is the sole reason that this
+ driver works with the 18C50 chip.
+
+ Thanks to Dave Newman (dnewman@crl.com) for providing initial patches for
+ the version 3.4 BIOS.
+
+ Thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for providing
+ patches that support the TMC-3260, a PCI bus card with the 36C70 chip.
+ The 36C70 chip appears to be "completely compatible" with the 18C30 chip.
+
+ Thanks to Eric Kasten (tigger@petroglyph.cl.msu.edu) for providing the
+ patch for the version 3.5 BIOS.
+
+ Thanks for Stephen Henson (shenson@nyx10.cs.du.edu) for providing the
+ patch for the Quantum ISA-200S SCSI adapter.
+ 
+ Thanks to Adam Bowen for the signature to the 1610M/MER/MEX scsi cards, to
+ Martin Andrews (andrewm@ccfadm.eeg.ccf.org) for the signature to some
+ random TMC-1680 repackaged by IBM; and to Mintak Ng (mintak@panix.com) for
+ the version 3.61 BIOS signature.
+
+ Thanks for Mark Singer (elf@netcom.com) and Richard Simpson
+ (rsimpson@ewrcsdra.demon.co.uk) for more Quantum signatures and detective
+ work on the Quantum RAM layout.
+
+ Special thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for
+ providing patches for proper PCI BIOS32-mediated detection of the TMC-3260
+ card (a PCI bus card with the 36C70 chip).  Please send James PCI-related
+ bug reports.
+
+ Thanks to Tom Cavin (tec@usa1.com) for preliminary command-line option
+ patches.
+ 
+ All of the alpha testers deserve much thanks.
+
+
+
+ NOTES ON USER DEFINABLE OPTIONS:
+
+ DEBUG: This turns on the printing of various debug information.
+
+ ENABLE_PARITY: This turns on SCSI parity checking.  With the current
+ driver, all attached devices must support SCSI parity.  If none of your
+ devices support parity, then you can probably get the driver to work by
+ turning this option off.  I have no way of testing this, however, and it
+ would appear that no one ever uses this option.
+
+ FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the
+ 18C30 chip have a 2k cache).  When this many 512 byte blocks are filled by
+ the SCSI device, an interrupt will be raised.  Therefore, this could be as
+ low as 0, or as high as 16.  Note, however, that values which are too high
+ or too low seem to prevent any interrupts from occurring, and thereby lock
+ up the machine.  I have found that 2 is a good number, but throughput may
+ be increased by changing this value to values which are close to 2.
+ Please let me know if you try any different values.
+
+ DO_DETECT: This activates some old scan code which was needed before the
+ high level drivers got fixed.  If you are having trouble with the driver,
+ turning this on should not hurt, and might help.  Please let me know if
+ this is the case, since this code will be removed from future drivers.
+
+ RESELECTION: This is no longer an option, since I gave up trying to
+ implement it in version 4.x of this driver.  It did not improve
+ performance at all and made the driver unstable (because I never found one
+ of the two race conditions which were introduced by the multiple
+ outstanding command code).  The instability seems a very high price to pay
+ just so that you don't have to wait for the tape to rewind.  If you want
+ this feature implemented, send me patches.  I'll be happy to send a copy
+ of my (broken) driver to anyone who would like to see a copy.
+
+ **************************************************************************/
+
+#ifdef PCMCIA
+#define MODULE
+#endif
+
+#ifdef MODULE
+#include <linux/module.h>
+#endif
+
+#ifdef PCMCIA
+#undef MODULE
+#endif
+
+#include <linux/sched.h>
+#include <asm/io.h>
+#include <linux/blk.h>
+#include "scsi.h"
+#include "hosts.h"
+#include "fdomain.h"
+#include <asm/system.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/proc_fs.h>
+#include <linux/bios32.h>
+#include <linux/pci.h>
+#include <linux/stat.h>
+
+#include <linux/config.h>	/* for CONFIG_PCI */
+
+struct proc_dir_entry proc_scsi_fdomain = {
+    PROC_SCSI_FDOMAIN, 7, "fdomain",
+    S_IFDIR | S_IRUGO | S_IXUGO, 2
+};
+  
+#define VERSION          "$Revision: 1.1 $"
+
+/* START OF USER DEFINABLE OPTIONS */
+
+#define DEBUG            1	/* Enable debugging output */
+#define ENABLE_PARITY    1	/* Enable SCSI Parity */
+#define FIFO_COUNT       2	/* Number of 512 byte blocks before INTR */
+#define DO_DETECT        0	/* Do device detection here (see scsi.c) */
+
+/* END OF USER DEFINABLE OPTIONS */
+
+#if DEBUG
+#define EVERY_ACCESS     0	/* Write a line on every scsi access */
+#define ERRORS_ONLY      1	/* Only write a line if there is an error */
+#define DEBUG_DETECT     0	/* Debug fdomain_16x0_detect() */
+#define DEBUG_MESSAGES   1	/* Debug MESSAGE IN phase */
+#define DEBUG_ABORT      1	/* Debug abort() routine */
+#define DEBUG_RESET      1	/* Debug reset() routine */
+#define DEBUG_RACE       1      /* Debug interrupt-driven race condition */
+#else
+#define EVERY_ACCESS     0	/* LEAVE THESE ALONE--CHANGE THE ONES ABOVE */
+#define ERRORS_ONLY      0
+#define DEBUG_DETECT     0
+#define DEBUG_MESSAGES   0
+#define DEBUG_ABORT      0
+#define DEBUG_RESET      0
+#define DEBUG_RACE       0
+#endif
+
+/* Errors are reported on the line, so we don't need to report them again */
+#if EVERY_ACCESS
+#undef ERRORS_ONLY
+#define ERRORS_ONLY      0
+#endif
+
+#if ENABLE_PARITY
+#define PARITY_MASK      0x08
+#else
+#define PARITY_MASK      0x00
+#endif
+
+enum chip_type {
+   unknown          = 0x00,
+   tmc1800          = 0x01,
+   tmc18c50         = 0x02,
+   tmc18c30         = 0x03,
+};
+
+enum {
+   in_arbitration   = 0x02,
+   in_selection     = 0x04,
+   in_other         = 0x08,
+   disconnect       = 0x10,
+   aborted          = 0x20,
+   sent_ident       = 0x40,
+};
+
+enum in_port_type {
+   Read_SCSI_Data   =  0,
+   SCSI_Status      =  1,
+   TMC_Status       =  2,
+   FIFO_Status      =  3,	/* tmc18c50/tmc18c30 only */
+   Interrupt_Cond   =  4,	/* tmc18c50/tmc18c30 only */
+   LSB_ID_Code      =  5,
+   MSB_ID_Code      =  6,
+   Read_Loopback    =  7,
+   SCSI_Data_NoACK  =  8,
+   Interrupt_Status =  9,
+   Configuration1   = 10,
+   Configuration2   = 11,	/* tmc18c50/tmc18c30 only */
+   Read_FIFO        = 12,
+   FIFO_Data_Count  = 14
+};
+
+enum out_port_type {
+   Write_SCSI_Data  =  0,
+   SCSI_Cntl        =  1,
+   Interrupt_Cntl   =  2,
+   SCSI_Mode_Cntl   =  3,
+   TMC_Cntl         =  4,
+   Memory_Cntl      =  5,	/* tmc18c50/tmc18c30 only */
+   Write_Loopback   =  7,
+   IO_Control       = 11,	/* tmc18c30 only */
+   Write_FIFO       = 12
+};
+
+static int               port_base         = 0;
+static void              *bios_base        = NULL;
+static int               bios_major        = 0;
+static int               bios_minor        = 0;
+static int               PCI_bus           = 0;
+static int               Quantum           = 0;	/* Quantum board variant */
+static int               interrupt_level   = 0;
+static volatile int      in_command        = 0;
+static Scsi_Cmnd         *current_SC       = NULL;
+static enum chip_type    chip              = unknown;
+static int               adapter_mask      = 0;
+static int               this_id           = 0;
+static int               setup_called      = 0;
+
+#if DEBUG_RACE
+static volatile int      in_interrupt_flag = 0;
+#endif
+
+static int               SCSI_Mode_Cntl_port;
+static int               FIFO_Data_Count_port;
+static int               Interrupt_Cntl_port;
+static int               Interrupt_Status_port;
+static int               Read_FIFO_port;
+static int               Read_SCSI_Data_port;
+static int               SCSI_Cntl_port;
+static int               SCSI_Data_NoACK_port;
+static int               SCSI_Status_port;
+static int               TMC_Cntl_port;
+static int               TMC_Status_port;
+static int               Write_FIFO_port;
+static int               Write_SCSI_Data_port;
+
+static int               FIFO_Size = 0x2000; /* 8k FIFO for
+						pre-tmc18c30 chips */
+
+extern void              fdomain_16x0_intr( int irq, void *dev_id, struct pt_regs * regs );
+
+static void *addresses[] = {
+   (void *)0xc8000,
+   (void *)0xca000,
+   (void *)0xce000,
+   (void *)0xde000,
+   (void *)0xcc000,		/* Extra addresses for PCI boards */
+   (void *)0xd0000,
+   (void *)0xe0000,
+};
+#define ADDRESS_COUNT (sizeof( addresses ) / sizeof( unsigned ))
+		       
+static unsigned short ports[] = { 0x140, 0x150, 0x160, 0x170 };
+#define PORT_COUNT (sizeof( ports ) / sizeof( unsigned short ))
+
+static unsigned short ints[] = { 3, 5, 10, 11, 12, 14, 15, 0 };
+
+/*
+
+  READ THIS BEFORE YOU ADD A SIGNATURE!
+
+  READING THIS SHORT NOTE CAN SAVE YOU LOTS OF TIME!
+
+  READ EVERY WORD, ESPECIALLY THE WORD *NOT*
+
+  This driver works *ONLY* for Future Domain cards using the TMC-1800,
+  TMC-18C50, or TMC-18C30 chip.  This includes models TMC-1650, 1660, 1670,
+  and 1680.
+
+  The following BIOS signature signatures are for boards which do *NOT*
+  work with this driver (these TMC-8xx and TMC-9xx boards may work with the
+  Seagate driver):
+
+  FUTURE DOMAIN CORP. (C) 1986-1988 V4.0I 03/16/88
+  FUTURE DOMAIN CORP. (C) 1986-1989 V5.0C2/14/89
+  FUTURE DOMAIN CORP. (C) 1986-1989 V6.0A7/28/89
+  FUTURE DOMAIN CORP. (C) 1986-1990 V6.0105/31/90
+  FUTURE DOMAIN CORP. (C) 1986-1990 V6.0209/18/90
+  FUTURE DOMAIN CORP. (C) 1986-1990 V7.009/18/90
+  FUTURE DOMAIN CORP. (C) 1992 V8.00.004/02/92
+
+*/
+
+struct signature {
+   const char *signature;
+   int  sig_offset;
+   int  sig_length;
+   int  major_bios_version;
+   int  minor_bios_version;
+   int  flag; /* 1 == PCI_bus, 2 == ISA_200S, 3 == ISA_250MG, 4 == ISA_200S */
+} signatures[] = {
+   /*          1         2         3         4         5         6 */
+   /* 123456789012345678901234567890123456789012345678901234567890 */
+   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89",  5, 50,  2,  0, 0 },
+   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V1.07/28/89",  5, 50,  2,  0, 0 },
+   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89", 72, 50,  2,  0, 2 },
+   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.0",        73, 43,  2,  0, 3 },
+   { "FUTURE DOMAIN CORP. (C) 1991 1800-V2.0.",            72, 39,  2,  0, 4 },
+   { "FUTURE DOMAIN CORP. (C) 1992 V3.00.004/02/92",        5, 44,  3,  0, 0 },
+   { "FUTURE DOMAIN TMC-18XX (C) 1993 V3.203/12/93",        5, 44,  3,  2, 0 },
+   { "IBM F1 P2 BIOS v1.0104/29/93",                        5, 28,  3, -1, 0 },
+   { "Future Domain Corp. V1.0008/18/93",                   5, 33,  3,  4, 0 },
+   { "Future Domain Corp. V1.0008/18/93",                  26, 33,  3,  4, 1 },
+   { "Adaptec AHA-2920 PCI-SCSI Card",                     42, 31,  3, -1, 1 },
+   { "IBM F1 P264/32",                                      5, 14,  3, -1, 1 },
+				/* This next signature may not be a 3.5 bios */
+   { "Future Domain Corp. V2.0108/18/93",                   5, 33,  3,  5, 0 },
+   { "FUTURE DOMAIN CORP.  V3.5008/18/93",                  5, 34,  3,  5, 0 },
+   { "FUTURE DOMAIN 18c30/18c50/1800 (C) 1994 V3.5",        5, 44,  3,  5, 0 },
+   { "FUTURE DOMAIN CORP.  V3.6008/18/93",                  5, 34,  3,  6, 0 },
+   { "FUTURE DOMAIN CORP.  V3.6108/18/93",                  5, 34,  3,  6, 0 },
+   { "FUTURE DOMAIN TMC-18XX",                              5, 22, -1, -1, 0 },
+
+   /* READ NOTICE ABOVE *BEFORE* YOU WASTE YOUR TIME ADDING A SIGNATURE
+    Also, fix the disk geometry code for your signature and send your
+    changes for faith@cs.unc.edu.  Above all, do *NOT* change any old
+    signatures!
+
+    Note that the last line will match a "generic" 18XX bios.  Because
+    Future Domain has changed the host SCSI ID and/or the location of the
+    geometry information in the on-board RAM area for each of the first
+    three BIOS's, it is still important to enter a fully qualified
+    signature in the table for any new BIOS's (after the host SCSI ID and
+    geometry location are verified). */
+};
+
+#define SIGNATURE_COUNT (sizeof( signatures ) / sizeof( struct signature ))
+
+static void print_banner( struct Scsi_Host *shpnt )
+{
+   if (!shpnt) return;		/* This won't ever happen */
+
+   if (bios_major < 0 && bios_minor < 0) {
+      printk( "scsi%d <fdomain>: No BIOS; using scsi id %d\n",
+	      shpnt->host_no, shpnt->this_id );
+   } else {
+      printk( "scsi%d <fdomain>: BIOS version ", shpnt->host_no );
+
+      if (bios_major >= 0) printk( "%d.", bios_major );
+      else                 printk( "?." );
+
+      if (bios_minor >= 0) printk( "%d", bios_minor );
+      else                 printk( "?." );
+   
+      printk( " at 0x%x using scsi id %d\n",
+	      (unsigned)bios_base, shpnt->this_id );
+   }
+
+				/* If this driver works for later FD PCI
+				   boards, we will have to modify banner
+				   for additional PCI cards, but for now if
+				   it's PCI it's a TMC-3260 - JTM */
+   printk( "scsi%d <fdomain>: %s chip at 0x%x irq ",
+	   shpnt->host_no,
+	   chip == tmc1800 ? "TMC-1800"
+	   : (chip == tmc18c50 ? "TMC-18C50"
+	      : (chip == tmc18c30 ?
+		 (PCI_bus ? "TMC-36C70 (PCI bus)" : "TMC-18C30")
+		 : "Unknown")),
+	   port_base );
+
+   if (interrupt_level) printk( "%d", interrupt_level );
+   else                 printk( "<none>" );
+
+   printk( "\n" );
+}
+
+void fdomain_setup( char *str, int *ints )
+{
+   if (setup_called++ || ints[0] < 2 || ints[0] > 3) {
+      printk( "fdomain: usage: fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>]\n" );
+      printk( "fdomain: bad LILO parameters?\n" );
+   }
+
+   port_base       = ints[0] >= 1 ? ints[1] : 0;
+   interrupt_level = ints[0] >= 2 ? ints[2] : 0;
+   this_id         = ints[0] >= 3 ? ints[3] : 0;
+   
+   bios_major = bios_minor = -1; /* Use geometry for BIOS version >= 3.4 */
+}
+
+
+static void do_pause( unsigned amount )	/* Pause for amount*10 milliseconds */
+{
+   unsigned long the_time = jiffies + amount; /* 0.01 seconds per jiffy */
+
+   while (jiffies < the_time);
+}
+
+inline static void fdomain_make_bus_idle( void )
+{
+   outb( 0, SCSI_Cntl_port );
+   outb( 0, SCSI_Mode_Cntl_port );
+   if (chip == tmc18c50 || chip == tmc18c30)
+	 outb( 0x21 | PARITY_MASK, TMC_Cntl_port ); /* Clear forced intr. */
+   else
+	 outb( 0x01 | PARITY_MASK, TMC_Cntl_port );
+}
+
+static int fdomain_is_valid_port( int port )
+{
+#if DEBUG_DETECT 
+   printk( " (%x%x),",
+	   inb( port + MSB_ID_Code ), inb( port + LSB_ID_Code ) );
+#endif
+
+   /* The MCA ID is a unique id for each MCA compatible board.  We
+      are using ISA boards, but Future Domain provides the MCA ID
+      anyway.  We can use this ID to ensure that this is a Future
+      Domain TMC-1660/TMC-1680.
+    */
+
+   if (inb( port + LSB_ID_Code ) != 0xe9) { /* test for 0x6127 id */
+      if (inb( port + LSB_ID_Code ) != 0x27) return 0;
+      if (inb( port + MSB_ID_Code ) != 0x61) return 0;
+      chip = tmc1800;
+   } else {				    /* test for 0xe960 id */
+      if (inb( port + MSB_ID_Code ) != 0x60) return 0;
+      chip = tmc18c50;
+
+#if 0
+
+				/* Try to toggle 32-bit mode.  This only
+				   works on an 18c30 chip.  (User reports
+				   say this works, so we should switch to
+				   it in the near future.) */
+
+      outb( 0x80, port + IO_Control );
+      if ((inb( port + Configuration2 ) & 0x80) == 0x80) {
+	 outb( 0x00, port + IO_Control );
+	 if ((inb( port + Configuration2 ) & 0x80) == 0x00) {
+	    chip = tmc18c30;
+	    FIFO_Size = 0x800;	/* 2k FIFO */
+	 }
+      }
+#else
+
+				/* That should have worked, but appears to
+				   have problems.  Let's assume it is an
+				   18c30 if the RAM is disabled. */
+
+      if (inb( port + Configuration2 ) & 0x02) {
+	 chip      = tmc18c30;
+	 FIFO_Size = 0x800;	/* 2k FIFO */
+      }
+#endif
+				/* If that failed, we are an 18c50. */
+   }
+
+   return 1;
+}
+
+static int fdomain_test_loopback( void )
+{
+   int i;
+   int result;
+
+   for (i = 0; i < 255; i++) {
+      outb( i, port_base + Write_Loopback );
+      result = inb( port_base + Read_Loopback );
+      if (i != result)
+	    return 1;
+   }
+   return 0;
+}
+
+/* fdomain_get_irq assumes that we have a valid MCA ID for a
+   TMC-1660/TMC-1680 Future Domain board.  Now, check to be sure the
+   bios_base matches these ports.  If someone was unlucky enough to have
+   purchased more than one Future Domain board, then they will have to
+   modify this code, as we only detect one board here.  [The one with the
+   lowest bios_base.]
+
+   Note that this routine is only used for systems without a PCI BIOS32
+   (e.g., ISA bus).  For PCI bus systems, this routine will likely fail
+   unless one of the IRQs listed in the ints array is used by the board.
+   Sometimes it is possible to use the computer's BIOS setup screen to
+   configure a PCI system so that one of these IRQs will be used by the
+   Future Domain card. */
+
+static int fdomain_get_irq( int base )
+{
+   int options = inb( base + Configuration1 );
+
+#if DEBUG_DETECT
+   printk( " Options = %x\n", options );
+#endif
+   
+				/* Check for board with lowest bios_base --
+				   this isn't valid for the 18c30 or for
+				   boards on the PCI bus, so just assume we
+				   have the right board. */
+
+   if (chip != tmc18c30
+       && !PCI_bus
+       && addresses[ (options & 0xc0) >> 6 ] != bios_base) return 0;
+
+   return ints[ (options & 0x0e) >> 1 ];
+}
+
+static int fdomain_isa_detect( int *irq, int *iobase )
+{
+   int i;
+   int base;
+   int flag = 0;
+
+   if (bios_major == 2) {
+      /* The TMC-1660/TMC-1680 has a RAM area just after the BIOS ROM.
+	 Assuming the ROM is enabled (otherwise we wouldn't have been
+	 able to read the ROM signature :-), then the ROM sets up the
+	 RAM area with some magic numbers, such as a list of port
+	 base addresses and a list of the disk "geometry" reported to
+	 DOS (this geometry has nothing to do with physical geometry).
+       */
+
+      switch (Quantum) {
+      case 2:			/* ISA_200S */
+      case 3:			/* ISA_250MG */
+	 base = *((char *)bios_base + 0x1fa2)
+	       + (*((char *)bios_base + 0x1fa3) << 8);
+	 break;
+      case 4:			/* ISA_200S (another one) */
+	 base = *((char *)bios_base + 0x1fa3)
+	       + (*((char *)bios_base + 0x1fa4) << 8);
+	 break;
+      default:
+	 base = *((char *)bios_base + 0x1fcc)
+	       + (*((char *)bios_base + 0x1fcd) << 8);
+	 break;
+      }
+   
+#if DEBUG_DETECT
+      printk( " %x,", base );
+#endif
+
+      for (flag = 0, i = 0; !flag && i < PORT_COUNT; i++) {
+	 if (base == ports[i])
+	       ++flag;
+      }
+
+      if (flag && fdomain_is_valid_port( base )) {
+	 *irq    = fdomain_get_irq( base );
+	 *iobase = base;
+	 return 1;
+      }
+      
+      /* This is a bad sign.  It usually means that someone patched the
+	 BIOS signature list (the signatures variable) to contain a BIOS
+	 signature for a board *OTHER THAN* the TMC-1660/TMC-1680. */
+      
+#if DEBUG_DETECT
+      printk( " RAM FAILED, " );
+#endif
+   }
+
+   /* Anyway, the alternative to finding the address in the RAM is to just
+      search through every possible port address for one that is attached
+      to the Future Domain card.  Don't panic, though, about reading all
+      these random port addresses -- there are rumors that the Future
+      Domain BIOS does something very similar.
+
+      Do not, however, check ports which the kernel knows are being used by
+      another driver. */
+
+   for (i = 0; i < PORT_COUNT; i++) {
+      base = ports[i];
+      if (check_region( base, 0x10 )) {
+#if DEBUG_DETECT
+	 printk( " (%x inuse),", base );
+#endif
+	 continue;
+      }
+#if DEBUG_DETECT
+      printk( " %x,", base );
+#endif
+      if ((flag = fdomain_is_valid_port( base ))) break;
+   }
+
+   if (!flag) return 0;		/* iobase not found */
+
+   *irq    = fdomain_get_irq( base );
+   *iobase = base;
+
+   return 1;			/* success */
+}
+
+static int fdomain_pci_nobios_detect( int *irq, int *iobase )
+{
+   int i;
+   int flag = 0;
+
+   /* The proper way of doing this is to use ask the PCI bus for the device
+      IRQ and interrupt level.  But we can't do that if PCI BIOS32 support
+      isn't compiled into the kernel, or if a PCI BIOS32 isn't present.
+
+      Instead, we scan down a bunch of addresses (Future Domain tech
+      support says we will probably find the address before we get to
+      0xf800).  This works fine on some systems -- other systems may have
+      to scan more addresses.  If you have to modify this section for your
+      installation, please send mail to faith@cs.unc.edu. */
+
+   for (i = 0xfff8; i > 0xe000; i -= 8) {
+      if (check_region( i, 0x10 )) {
+#if DEBUG_DETECT
+	 printk( " (%x inuse)," , i );
+#endif
+	 continue;
+      }
+      if ((flag = fdomain_is_valid_port( i ))) break;
+   }
+
+   if (!flag) return 0;		/* iobase not found */
+
+   *irq    = fdomain_get_irq( i );
+   *iobase = i;
+
+   return 1;			/* success */
+}
+
+/* PCI detection function: int fdomain_pci_bios_detect(int* irq, int*
+   iobase) This function gets the Interrupt Level and I/O base address from
+   the PCI configuration registers.  The I/O base address is masked with
+   0xfff8 since on my card the address read from the PCI config registers
+   is off by one from the actual I/O base address necessary for accessing
+   the status and control registers on the card (PCI config register gives
+   0xf801, actual address is 0xf800).  This is likely a bug in the FD
+   config code that writes to the PCI registers, however using a mask
+   should be safe since I think the scan done by the card to determine the
+   I/O base is done in increments of 8 (i.e., 0xf800, 0xf808, ...), at
+   least the old scan code we used to use to get the I/O base did...  Also,
+   the device ID from the PCI config registers is 0x0 and should be 0x60e9
+   as it is in the status registers (offset 5 from I/O base).  If this is
+   changed in future hardware/BIOS changes it will need to be fixed in this
+   detection function.  Comments, bug reports, etc... on this function
+   should be sent to mckinley@msupa.pa.msu.edu - James T. McKinley.  */
+
+#ifdef CONFIG_PCI
+static int fdomain_pci_bios_detect( int *irq, int *iobase )
+{
+   int              error;
+   unsigned char    pci_bus, pci_dev_fn;    /* PCI bus & device function */
+   unsigned char    pci_irq;                /* PCI interrupt line */
+   unsigned int     pci_base;               /* PCI I/O base address */
+   unsigned short   pci_vendor, pci_device; /* PCI vendor & device IDs */
+
+   /* If the PCI BIOS doesn't exist, use the old-style detection routines.
+      Otherwise, get the I/O base address and interrupt from the PCI config
+      registers. */
+   
+   if (!pcibios_present()) return fdomain_pci_nobios_detect( irq, iobase );
+
+#if DEBUG_DETECT
+   /* Tell how to print a list of the known PCI devices from bios32 and
+      list vendor and device IDs being used if in debug mode.  */
+      
+   printk( "\nINFO: cat /proc/pci to see list of PCI devices from bios32\n" );
+   printk( "\nTMC-3260 detect:"
+	   " Using PCI Vendor ID: 0x%x, PCI Device ID: 0x%x\n",
+	   PCI_VENDOR_ID_FD, 
+	   PCI_DEVICE_ID_FD_36C70 );
+#endif 
+
+   /* We will have to change this if more than 1 PCI bus is present and the
+      FD scsi host is not on the first bus (i.e., a PCI to PCI bridge,
+      which is not supported by bios32 right now anyway).  This should
+      probably be done by a call to pcibios_find_device but I can't get it
+      to work...  Also the device ID reported from the PCI config registers
+      does not match the device ID quoted in the tech manual or available
+      from offset 5 from the I/O base address.  It should be 0x60E9, but it
+      is 0x0 if read from the PCI config registers.  I guess the FD folks
+      neglected to write it to the PCI registers...  This loop is necessary
+      to get the device function (at least until someone can get
+      pcibios_find_device to work, I cannot but 53c7,8xx.c uses it...). */
+    
+   pci_bus = 0;
+
+   for (pci_dev_fn = 0x0; pci_dev_fn < 0xff; pci_dev_fn++) {
+      pcibios_read_config_word( pci_bus,
+				pci_dev_fn,
+				PCI_VENDOR_ID,
+				&pci_vendor );
+
+      if (pci_vendor == PCI_VENDOR_ID_FD) {
+	 pcibios_read_config_word( pci_bus,
+				   pci_dev_fn,
+				   PCI_DEVICE_ID,
+				   &pci_device );
+
+	 if (pci_device == PCI_DEVICE_ID_FD_36C70) {
+	    /* Break out once we have the correct device.  If other FD
+	       PCI devices are added to this driver we will need to add
+	       an or of the other PCI_DEVICE_ID_FD_XXXXX's here. */
+	    break;
+	 } else {
+	    /* If we can't find an FD scsi card we give up. */
+	    return 0;
+	 }
+      }
+   }
+       
+#if DEBUG_DETECT
+   printk( "Future Domain 36C70 : at PCI bus %u, device %u, function %u\n",
+	   pci_bus,
+	   (pci_dev_fn & 0xf8) >> 3, 
+	   pci_dev_fn & 7 );
+#endif
+
+   /* We now have the appropriate device function for the FD board so we
+      just read the PCI config info from the registers.  */
+
+   if ((error = pcibios_read_config_dword( pci_bus,
+					   pci_dev_fn, 
+					   PCI_BASE_ADDRESS_0,
+					   &pci_base ))
+       || (error = pcibios_read_config_byte( pci_bus,
+					     pci_dev_fn, 
+					     PCI_INTERRUPT_LINE,
+					     &pci_irq ))) {
+      printk ( "PCI ERROR: Future Domain 36C70 not initializing"
+	       " due to error reading configuration space\n" );
+      return 0;
+   } else {
+#if DEBUG_DETECT
+      printk( "TMC-3260 PCI: IRQ = %u, I/O base = 0x%lx\n", 
+	      pci_irq, pci_base );
+#endif
+
+      /* Now we have the I/O base address and interrupt from the PCI
+	 configuration registers.  Unfortunately it seems that the I/O base
+	 address is off by one on my card so I mask it with 0xfff8.  This
+	 must be some kind of goof in the FD code that does the autoconfig
+	 and writes to the PCI registers (or maybe I just don't understand
+	 something).  If they fix it in later versions of the card or BIOS
+	 we may have to adjust the address based on the signature or
+	 something...  */
+
+      *irq    = pci_irq;
+      *iobase = (pci_base & 0xfff8);
+
+#if DEBUG_DETECT
+      printk( "TMC-3260 fix: Masking I/O base address with 0xff00.\n" ); 
+      printk( "TMC-3260: IRQ = %d, I/O base = 0x%x\n", *irq, *iobase );
+#endif
+
+      if (!fdomain_is_valid_port( *iobase )) return 0;
+      return 1;
+   }
+   return 0;
+}
+#endif
+
+int fdomain_16x0_detect( Scsi_Host_Template *tpnt )
+{
+   int              i, j;
+   int              retcode;
+   struct Scsi_Host *shpnt;
+#if DO_DETECT
+   const int        buflen = 255;
+   Scsi_Cmnd        SCinit;
+   unsigned char    do_inquiry[] =       { INQUIRY, 0, 0, 0, buflen, 0 };
+   unsigned char    do_request_sense[] = { REQUEST_SENSE, 0, 0, 0, buflen, 0 };
+   unsigned char    do_read_capacity[] = { READ_CAPACITY,
+					   0, 0, 0, 0, 0, 0, 0, 0, 0 };
+   unsigned char    buf[buflen];
+#endif
+
+#if DEBUG_DETECT
+   printk( "fdomain_16x0_detect()," );
+#endif
+   tpnt->proc_dir = &proc_scsi_fdomain;
+
+   if (setup_called) {
+#if DEBUG_DETECT
+      printk( "no BIOS, using port_base = 0x%x, irq = %d\n",
+	      port_base, interrupt_level );
+#endif
+      if (!fdomain_is_valid_port( port_base )) {
+	 printk( "fdomain: cannot locate chip at port base 0x%x\n",
+		 port_base );
+	 printk( "fdomain: bad LILO parameters?\n" );
+	 return 0;
+      }
+   } else {
+      int flag = 0;
+      
+      for (i = 0; !bios_base && i < ADDRESS_COUNT; i++) {
+#if DEBUG_DETECT
+	 printk( " %x(%x),", (unsigned)addresses[i], (unsigned)bios_base );
+#endif
+	 for (j = 0; !bios_base && j < SIGNATURE_COUNT; j++) {
+	    if (!memcmp( ((char *)addresses[i] + signatures[j].sig_offset),
+			 signatures[j].signature, signatures[j].sig_length )) {
+	       bios_major = signatures[j].major_bios_version;
+	       bios_minor = signatures[j].minor_bios_version;
+	       PCI_bus    = (signatures[j].flag == 1);
+	       Quantum    = (signatures[j].flag > 1) ? signatures[j].flag : 0;
+	       bios_base  = addresses[i];
+	    }
+	 }
+      }
+
+      if (!bios_base) {
+#if DEBUG_DETECT
+	 printk( " FAILED: NO BIOS\n" );
+#endif
+	 return 0;
+      }
+
+      if (!PCI_bus) {
+	 flag = fdomain_isa_detect( &interrupt_level, &port_base );
+      } else {
+#ifdef CONFIG_PCI
+	 flag = fdomain_pci_bios_detect( &interrupt_level, &port_base );
+#else
+	 flag = fdomain_pci_nobios_detect( &interrupt_level, &port_base );
+#endif
+      }
+	 
+      if (!flag) {
+#if DEBUG_DETECT
+	 printk( " FAILED: NO PORT\n" );
+#endif
+#ifdef CONFIG_PCI
+	 printk( "\nTMC-3260 36C70 PCI scsi chip detection failed.\n" );
+	 printk( "Send mail to mckinley@msupa.pa.msu.edu.\n" );
+#endif
+	 return 0;		/* Cannot find valid set of ports */
+      }
+   }
+
+   SCSI_Mode_Cntl_port   = port_base + SCSI_Mode_Cntl;
+   FIFO_Data_Count_port  = port_base + FIFO_Data_Count;
+   Interrupt_Cntl_port   = port_base + Interrupt_Cntl;
+   Interrupt_Status_port = port_base + Interrupt_Status;
+   Read_FIFO_port        = port_base + Read_FIFO;
+   Read_SCSI_Data_port   = port_base + Read_SCSI_Data;
+   SCSI_Cntl_port        = port_base + SCSI_Cntl;
+   SCSI_Data_NoACK_port  = port_base + SCSI_Data_NoACK;
+   SCSI_Status_port      = port_base + SCSI_Status;
+   TMC_Cntl_port         = port_base + TMC_Cntl;
+   TMC_Status_port       = port_base + TMC_Status;
+   Write_FIFO_port       = port_base + Write_FIFO;
+   Write_SCSI_Data_port  = port_base + Write_SCSI_Data;
+
+   fdomain_16x0_reset( NULL, 0 );
+
+   if (fdomain_test_loopback()) {
+#if DEBUG_DETECT
+      printk( "fdomain: LOOPBACK TEST FAILED, FAILING DETECT!\n" );
+#endif
+      if (setup_called) {
+	 printk( "fdomain: loopback test failed at port base 0x%x\n",
+		 port_base );
+	 printk( "fdomain: bad LILO parameters?\n" );
+      }
+      return 0;
+   }
+
+   if (this_id) {
+      tpnt->this_id = (this_id & 0x07);
+      adapter_mask  = (1 << tpnt->this_id);
+   } else {
+      if (PCI_bus || (bios_major == 3 && bios_minor >= 2) || bios_major < 0) {
+	 tpnt->this_id = 7;
+	 adapter_mask  = 0x80;
+      } else {
+	 tpnt->this_id = 6;
+	 adapter_mask  = 0x40;
+      }
+   }
+
+				/* Print out a banner here in case we can't
+				   get resources.  */
+
+   shpnt = scsi_register( tpnt, 0 );
+   shpnt->irq = interrupt_level;
+   shpnt->io_port = port_base;
+   shpnt->n_io_port = 0x10;
+   print_banner( shpnt );
+
+				/* Log IRQ with kernel */   
+   if (!interrupt_level) {
+      panic( "fdomain: *NO* interrupt level selected!\n" );
+   } else {
+      /* Register the IRQ with the kernel */
+
+      retcode = request_irq( interrupt_level,
+			     fdomain_16x0_intr, SA_INTERRUPT, "fdomain", NULL);
+
+      if (retcode < 0) {
+	 if (retcode == -EINVAL) {
+	    printk( "fdomain: IRQ %d is bad!\n", interrupt_level );
+	    printk( "         This shouldn't happen!\n" );
+	    printk( "         Send mail to faith@cs.unc.edu\n" );
+	 } else if (retcode == -EBUSY) {
+	    printk( "fdomain: IRQ %d is already in use!\n", interrupt_level );
+	    printk( "         Please use another IRQ!\n" );
+	 } else {
+	    printk( "fdomain: Error getting IRQ %d\n", interrupt_level );
+	    printk( "         This shouldn't happen!\n" );
+	    printk( "         Send mail to faith@cs.unc.edu\n" );
+	 }
+	 panic( "fdomain: Driver requires interruptions\n" );
+      }
+   }
+
+				/* Log I/O ports with kernel */
+   request_region( port_base, 0x10, "fdomain" );
+
+#if DO_DETECT
+
+   /* These routines are here because of the way the SCSI bus behaves after
+      a reset.  This appropriate behavior was not handled correctly by the
+      higher level SCSI routines when I first wrote this driver.  Now,
+      however, correct scan routines are part of scsi.c and these routines
+      are no longer needed.  However, this code is still good for
+      debugging.  */
+
+   SCinit.request_buffer  = SCinit.buffer = buf;
+   SCinit.request_bufflen = SCinit.bufflen = sizeof(buf)-1;
+   SCinit.use_sg          = 0;
+   SCinit.lun             = 0;
+
+   printk( "fdomain: detection routine scanning for devices:\n" );
+   for (i = 0; i < 8; i++) {
+      SCinit.target = i;
+      if (i == tpnt->this_id)	/* Skip host adapter */
+	    continue;
+      memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense));
+      retcode = fdomain_16x0_command(&SCinit);
+      if (!retcode) {
+	 memcpy(SCinit.cmnd, do_inquiry, sizeof(do_inquiry));
+	 retcode = fdomain_16x0_command(&SCinit);
+	 if (!retcode) {
+	    printk( "     SCSI ID %d: ", i );
+	    for (j = 8; j < (buf[4] < 32 ? buf[4] : 32); j++)
+		  printk( "%c", buf[j] >= 20 ? buf[j] : ' ' );
+	    memcpy(SCinit.cmnd, do_read_capacity, sizeof(do_read_capacity));
+	    retcode = fdomain_16x0_command(&SCinit);
+	    if (!retcode) {
+	       unsigned long blocks, size, capacity;
+	       
+	       blocks = (buf[0] << 24) | (buf[1] << 16)
+		     | (buf[2] << 8) | buf[3];
+	       size = (buf[4] << 24) | (buf[5] << 16) | (buf[6] << 8) | buf[7];
+	       capacity = +( +(blocks / 1024L) * +(size * 10L)) / 1024L;
+	       
+	       printk( "%lu MB (%lu byte blocks)",
+		       ((capacity + 5L) / 10L), size );
+	    } else {
+	       memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense));
+	       retcode = fdomain_16x0_command(&SCinit);
+	    }
+	    printk ("\n" );
+	 } else {
+	    memcpy(SCinit.cmnd, do_request_sense, sizeof(do_request_sense));
+	    retcode = fdomain_16x0_command(&SCinit);
+	 }
+      }
+   }
+#endif
+
+   return 1;			/* Maximum of one adapter will be detected. */
+}
+
+const char *fdomain_16x0_info( struct Scsi_Host *ignore )
+{
+   static char buffer[80];
+   char        *pt;
+   
+   strcpy( buffer, "Future Domain TMC-16x0 SCSI driver, version" );
+   if (strchr( VERSION, ':')) { /* Assume VERSION is an RCS Revision string */
+      strcat( buffer, strchr( VERSION, ':' ) + 1 );
+      pt = strrchr( buffer, '$') - 1;
+      if (!pt)  		/* Stripped RCS Revision string? */
+	    pt = buffer + strlen( buffer ) - 1;
+      if (*pt != ' ')
+	    ++pt;
+      *pt = '\0';
+   } else {			/* Assume VERSION is a number */
+      strcat( buffer, " " VERSION );
+   }
+      
+   return buffer;
+}
+
+				/* First pass at /proc information routine. */
+/*
+ * inout : decides on the direction of the dataflow and the meaning of the 
+ *         variables
+ * buffer: If inout==FALSE data is being written to it else read from it
+ * *start: If inout==FALSE start of the valid data in the buffer
+ * offset: If inout==FALSE offset from the beginning of the imaginary file 
+ *         from which we start writing into the buffer
+ * length: If inout==FALSE max number of bytes to be written into the buffer 
+ *         else number of bytes in the buffer
+ */
+int fdomain_16x0_proc_info( char *buffer, char **start, off_t offset,
+			    int length, int hostno, int inout )
+{
+   const char *info = fdomain_16x0_info( NULL );
+   int        len;
+   int        pos;
+   int        begin;
+
+   if (inout) return(-ENOSYS);
+    
+   begin = 0;
+   strcpy( buffer, info );
+   strcat( buffer, "\n" );
+
+   pos = len = strlen( buffer );
+
+   if(pos < offset) {
+      len = 0;
+      begin = pos;
+   }
+    
+   *start = buffer + (offset - begin);   /* Start of wanted data */
+   len -= (offset - begin);
+   if(len > length) len = length;
+   
+   return(len);
+}
+   
+#if 0
+static int fdomain_arbitrate( void )
+{
+   int           status = 0;
+   unsigned long timeout;
+
+#if EVERY_ACCESS
+   printk( "fdomain_arbitrate()\n" );
+#endif
+   
+   outb( 0x00, SCSI_Cntl_port );              /* Disable data drivers */
+   outb( adapter_mask, port_base + SCSI_Data_NoACK ); /* Set our id bit */
+   outb( 0x04 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */
+
+   timeout = jiffies + 50;		      /* 500 mS */
+   while (jiffies < timeout) {
+      status = inb( TMC_Status_port );        /* Read adapter status */
+      if (status & 0x02)		      /* Arbitration complete */
+	    return 0;	
+   }
+
+   /* Make bus idle */
+   fdomain_make_bus_idle();
+
+#if EVERY_ACCESS
+   printk( "Arbitration failed, status = %x\n", status );
+#endif
+#if ERRORS_ONLY
+   printk( "fdomain: Arbitration failed, status = %x\n", status );
+#endif
+   return 1;
+}
+#endif
+
+static int fdomain_select( int target )
+{
+   int           status;
+   unsigned long timeout;
+   static int    flag = 0;
+
+
+   outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */
+   outb( adapter_mask | (1 << target), SCSI_Data_NoACK_port );
+
+   /* Stop arbitration and enable parity */
+   outb( PARITY_MASK, TMC_Cntl_port ); 
+
+   timeout = jiffies + 35;		/* 350mS -- because of timeouts
+					   (was 250mS) */
+
+   while (jiffies < timeout) {
+      status = inb( SCSI_Status_port ); /* Read adapter status */
+      if (status & 1) {			/* Busy asserted */
+	 /* Enable SCSI Bus (on error, should make bus idle with 0) */
+	 outb( 0x80, SCSI_Cntl_port );
+	 return 0;
+      }
+   }
+   /* Make bus idle */
+   fdomain_make_bus_idle();
+#if EVERY_ACCESS
+   if (!target) printk( "Selection failed\n" );
+#endif
+#if ERRORS_ONLY
+   if (!target) {
+      if (!flag) /* Skip first failure for all chips. */
+	    ++flag;
+      else
+	    printk( "fdomain: Selection failed\n" );
+   }
+#endif
+   return 1;
+}
+
+void my_done( int error )
+{
+   if (in_command) {
+      in_command = 0;
+      outb( 0x00, Interrupt_Cntl_port );
+      fdomain_make_bus_idle();
+      current_SC->result = error;
+      if (current_SC->scsi_done)
+	    current_SC->scsi_done( current_SC );
+      else panic( "fdomain: current_SC->scsi_done() == NULL" );
+   } else {
+      panic( "fdomain: my_done() called outside of command\n" );
+   }
+#if DEBUG_RACE
+   in_interrupt_flag = 0;
+#endif
+}
+
+void fdomain_16x0_intr( int irq, void *dev_id, struct pt_regs * regs )
+{
+   int      status;
+   int      done = 0;
+   unsigned data_count;
+
+				/* The fdomain_16x0_intr is only called via
+				   the interrupt handler.  The goal of the
+				   sti() here is to allow other
+				   interruptions while this routine is
+				   running. */
+
+   sti();			/* Yes, we really want sti() here */
+   
+   outb( 0x00, Interrupt_Cntl_port );
+
+   /* We usually have one spurious interrupt after each command.  Ignore it. */
+   if (!in_command || !current_SC) {	/* Spurious interrupt */
+#if EVERY_ACCESS
+      printk( "Spurious interrupt, in_command = %d, current_SC = %x\n",
+	      in_command, current_SC );
+#endif
+      return;
+   }
+
+   /* Abort calls my_done, so we do nothing here. */
+   if (current_SC->SCp.phase & aborted) {
+#if DEBUG_ABORT
+      printk( "Interrupt after abort, ignoring\n" );
+#endif
+      /*
+      return; */
+   }
+
+#if DEBUG_RACE
+   ++in_interrupt_flag;
+#endif
+
+   if (current_SC->SCp.phase & in_arbitration) {
+      status = inb( TMC_Status_port );        /* Read adapter status */
+      if (!(status & 0x02)) {
+#if EVERY_ACCESS
+	 printk( " AFAIL " );
+#endif
+	 my_done( DID_BUS_BUSY << 16 );
+	 return;
+      }
+      current_SC->SCp.phase = in_selection;
+      
+      outb( 0x40 | FIFO_COUNT, Interrupt_Cntl_port );
+
+      outb( 0x82, SCSI_Cntl_port ); /* Bus Enable + Select */
+      outb( adapter_mask | (1 << current_SC->target), SCSI_Data_NoACK_port );
+      
+      /* Stop arbitration and enable parity */
+      outb( 0x10 | PARITY_MASK, TMC_Cntl_port );
+#if DEBUG_RACE
+      in_interrupt_flag = 0;
+#endif
+      return;
+   } else if (current_SC->SCp.phase & in_selection) {
+      status = inb( SCSI_Status_port );
+      if (!(status & 0x01)) {
+	 /* Try again, for slow devices */
+	 if (fdomain_select( current_SC->target )) {
+#if EVERY_ACCESS
+	    printk( " SFAIL " );
+#endif
+	    my_done( DID_NO_CONNECT << 16 );
+	    return;
+	 } else {
+#if EVERY_ACCESS
+	    printk( " AltSel " );
+#endif
+	    /* Stop arbitration and enable parity */
+	    outb( 0x10 | PARITY_MASK, TMC_Cntl_port );
+	 }
+      }
+      current_SC->SCp.phase = in_other;
+      outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port );
+      outb( 0x80, SCSI_Cntl_port );
+#if DEBUG_RACE
+      in_interrupt_flag = 0;
+#endif
+      return;
+   }
+   
+   /* current_SC->SCp.phase == in_other: this is the body of the routine */
+   
+   status = inb( SCSI_Status_port );
+   
+   if (status & 0x10) {	/* REQ */
+      
+      switch (status & 0x0e) {
+       
+      case 0x08:		/* COMMAND OUT */
+	 outb( current_SC->cmnd[current_SC->SCp.sent_command++],
+	       Write_SCSI_Data_port );
+#if EVERY_ACCESS
+	 printk( "CMD = %x,",
+		 current_SC->cmnd[ current_SC->SCp.sent_command - 1] );
+#endif
+	 break;
+      case 0x00:		/* DATA OUT -- tmc18c50/tmc18c30 only */
+	 if (chip != tmc1800 && !current_SC->SCp.have_data_in) {
+	    current_SC->SCp.have_data_in = -1;
+	    outb( 0xd0 | PARITY_MASK, TMC_Cntl_port );
+	 }
+	 break;
+      case 0x04:		/* DATA IN -- tmc18c50/tmc18c30 only */
+	 if (chip != tmc1800 && !current_SC->SCp.have_data_in) {
+	    current_SC->SCp.have_data_in = 1;
+	    outb( 0x90 | PARITY_MASK, TMC_Cntl_port );
+	 }
+	 break;
+      case 0x0c:		/* STATUS IN */
+	 current_SC->SCp.Status = inb( Read_SCSI_Data_port );
+#if EVERY_ACCESS
+	 printk( "Status = %x, ", current_SC->SCp.Status );
+#endif
+#if ERRORS_ONLY
+	 if (current_SC->SCp.Status
+	     && current_SC->SCp.Status != 2
+	     && current_SC->SCp.Status != 8) {
+	    printk( "fdomain: target = %d, command = %x, status = %x\n",
+		    current_SC->target,
+		    current_SC->cmnd[0],
+		    current_SC->SCp.Status );
+	 }
+#endif
+	       break;
+      case 0x0a:		/* MESSAGE OUT */
+	 outb( MESSAGE_REJECT, Write_SCSI_Data_port ); /* Reject */
+	 break;
+      case 0x0e:		/* MESSAGE IN */
+	 current_SC->SCp.Message = inb( Read_SCSI_Data_port );
+#if EVERY_ACCESS
+	 printk( "Message = %x, ", current_SC->SCp.Message );
+#endif
+	 if (!current_SC->SCp.Message) ++done;
+#if DEBUG_MESSAGES || EVERY_ACCESS
+	 if (current_SC->SCp.Message) {
+	    printk( "fdomain: message = %x\n", current_SC->SCp.Message );
+	 }
+#endif
+	 break;
+      }
+   }
+
+   if (chip == tmc1800
+       && !current_SC->SCp.have_data_in
+       && (current_SC->SCp.sent_command
+	   >= current_SC->cmd_len)) {
+				/* We have to get the FIFO direction
+				   correct, so I've made a table based
+				   on the SCSI Standard of which commands
+				   appear to require a DATA OUT phase.
+				 */
+      /*
+	p. 94: Command for all device types
+	CHANGE DEFINITION            40 DATA OUT
+	COMPARE                      39 DATA OUT
+	COPY                         18 DATA OUT
+	COPY AND VERIFY              3a DATA OUT
+	INQUIRY                      12 
+	LOG SELECT                   4c DATA OUT
+	LOG SENSE                    4d
+	MODE SELECT (6)              15 DATA OUT
+	MODE SELECT (10)             55 DATA OUT
+	MODE SENSE (6)               1a
+	MODE SENSE (10)              5a
+	READ BUFFER                  3c
+	RECEIVE DIAGNOSTIC RESULTS   1c
+	REQUEST SENSE                03
+	SEND DIAGNOSTIC              1d DATA OUT
+	TEST UNIT READY              00
+	WRITE BUFFER                 3b DATA OUT
+
+	p.178: Commands for direct-access devices (not listed on p. 94)
+	FORMAT UNIT                  04 DATA OUT
+	LOCK-UNLOCK CACHE            36
+	PRE-FETCH                    34
+	PREVENT-ALLOW MEDIUM REMOVAL 1e
+	READ (6)/RECEIVE             08
+	READ (10)                    3c
+	READ CAPACITY                25
+	READ DEFECT DATA (10)        37
+	READ LONG                    3e
+	REASSIGN BLOCKS              07 DATA OUT
+	RELEASE                      17
+	RESERVE                      16 DATA OUT
+	REZERO UNIT/REWIND           01
+	SEARCH DATA EQUAL (10)       31 DATA OUT
+	SEARCH DATA HIGH (10)        30 DATA OUT
+	SEARCH DATA LOW (10)         32 DATA OUT
+	SEEK (6)                     0b
+	SEEK (10)                    2b
+	SET LIMITS (10)              33
+	START STOP UNIT              1b
+	SYNCHRONIZE CACHE            35
+	VERIFY (10)                  2f
+	WRITE (6)/PRINT/SEND         0a DATA OUT
+	WRITE (10)/SEND              2a DATA OUT
+	WRITE AND VERIFY (10)        2e DATA OUT
+	WRITE LONG                   3f DATA OUT
+	WRITE SAME                   41 DATA OUT ?
+
+	p. 261: Commands for sequential-access devices (not previously listed)
+	ERASE                        19
+	LOAD UNLOAD                  1b
+	LOCATE                       2b
+	READ BLOCK LIMITS            05
+	READ POSITION                34
+	READ REVERSE                 0f
+	RECOVER BUFFERED DATA        14
+	SPACE                        11
+	WRITE FILEMARKS              10 ?
+
+	p. 298: Commands for printer devices (not previously listed)
+	****** NOT SUPPORTED BY THIS DRIVER, since 0b is SEEK (6) *****
+	SLEW AND PRINT               0b DATA OUT  -- same as seek
+	STOP PRINT                   1b
+	SYNCHRONIZE BUFFER           10
+
+	p. 315: Commands for processor devices (not previously listed)
+	
+	p. 321: Commands for write-once devices (not previously listed)
+	MEDIUM SCAN                  38
+	READ (12)                    a8
+	SEARCH DATA EQUAL (12)       b1 DATA OUT
+	SEARCH DATA HIGH (12)        b0 DATA OUT
+	SEARCH DATA LOW (12)         b2 DATA OUT
+	SET LIMITS (12)              b3
+	VERIFY (12)                  af
+	WRITE (12)                   aa DATA OUT
+	WRITE AND VERIFY (12)        ae DATA OUT
+
+	p. 332: Commands for CD-ROM devices (not previously listed)
+	PAUSE/RESUME                 4b
+	PLAY AUDIO (10)              45
+	PLAY AUDIO (12)              a5
+	PLAY AUDIO MSF               47
+	PLAY TRACK RELATIVE (10)     49
+	PLAY TRACK RELATIVE (12)     a9
+	READ HEADER                  44
+	READ SUB-CHANNEL             42
+	READ TOC                     43
+
+	p. 370: Commands for scanner devices (not previously listed)
+	GET DATA BUFFER STATUS       34
+	GET WINDOW                   25
+	OBJECT POSITION              31
+	SCAN                         1b
+	SET WINDOW                   24 DATA OUT
+
+	p. 391: Commands for optical memory devices (not listed)
+	ERASE (10)                   2c
+	ERASE (12)                   ac
+	MEDIUM SCAN                  38 DATA OUT
+	READ DEFECT DATA (12)        b7
+	READ GENERATION              29
+	READ UPDATED BLOCK           2d
+	UPDATE BLOCK                 3d DATA OUT
+
+	p. 419: Commands for medium changer devices (not listed)
+	EXCHANGE MEDIUM              46
+	INITIALIZE ELEMENT STATUS    07
+	MOVE MEDIUM                  a5
+	POSITION TO ELEMENT          2b
+	READ ELEMENT STATUS          b8
+	REQUEST VOL. ELEMENT ADDRESS b5
+	SEND VOLUME TAG              b6 DATA OUT
+
+	p. 454: Commands for communications devices (not listed previously)
+	GET MESSAGE (6)              08
+	GET MESSAGE (10)             28
+	GET MESSAGE (12)             a8
+      */
+	
+      switch (current_SC->cmnd[0]) {
+      case CHANGE_DEFINITION: case COMPARE:         case COPY:
+      case COPY_VERIFY:       case LOG_SELECT:      case MODE_SELECT:
+      case MODE_SELECT_10:    case SEND_DIAGNOSTIC: case WRITE_BUFFER:
+
+      case FORMAT_UNIT:       case REASSIGN_BLOCKS: case RESERVE:
+      case SEARCH_EQUAL:      case SEARCH_HIGH:     case SEARCH_LOW:
+      case WRITE_6:           case WRITE_10:        case WRITE_VERIFY:
+      case 0x3f:              case 0x41:
+
+      case 0xb1:              case 0xb0:            case 0xb2:
+      case 0xaa:              case 0xae:
+
+      case 0x24:
+
+      case 0x38:              case 0x3d:
+
+      case 0xb6:
+	 
+      case 0xea:		/* alternate number for WRITE LONG */
+	 
+	 current_SC->SCp.have_data_in = -1;
+	 outb( 0xd0 | PARITY_MASK, TMC_Cntl_port );
+	 break;
+
+      case 0x00:
+      default:
+	 
+	 current_SC->SCp.have_data_in = 1;
+	 outb( 0x90 | PARITY_MASK, TMC_Cntl_port );
+	 break;
+      }
+   }
+
+   if (current_SC->SCp.have_data_in == -1) { /* DATA OUT */
+      while ( (data_count = FIFO_Size - inw( FIFO_Data_Count_port )) > 512 ) {
+#if EVERY_ACCESS
+	 printk( "DC=%d, ", data_count ) ;
+#endif
+	 if (data_count > current_SC->SCp.this_residual)
+	       data_count = current_SC->SCp.this_residual;
+	 if (data_count > 0) {
+#if EVERY_ACCESS
+	    printk( "%d OUT, ", data_count );
+#endif
+	    if (data_count == 1) {
+	       outb( *current_SC->SCp.ptr++, Write_FIFO_port );
+	       --current_SC->SCp.this_residual;
+	    } else {
+	       data_count >>= 1;
+	       outsw( Write_FIFO_port, current_SC->SCp.ptr, data_count );
+	       current_SC->SCp.ptr += 2 * data_count;
+	       current_SC->SCp.this_residual -= 2 * data_count;
+	    }
+	 }
+	 if (!current_SC->SCp.this_residual) {
+	    if (current_SC->SCp.buffers_residual) {
+	       --current_SC->SCp.buffers_residual;
+	       ++current_SC->SCp.buffer;
+	       current_SC->SCp.ptr = current_SC->SCp.buffer->address;
+	       current_SC->SCp.this_residual = current_SC->SCp.buffer->length;
+	    } else
+		  break;
+	 }
+      }
+   }
+   
+   if (current_SC->SCp.have_data_in == 1) { /* DATA IN */
+      while ((data_count = inw( FIFO_Data_Count_port )) > 0) {
+#if EVERY_ACCESS
+	 printk( "DC=%d, ", data_count );
+#endif
+	 if (data_count > current_SC->SCp.this_residual)
+	       data_count = current_SC->SCp.this_residual;
+	 if (data_count) {
+#if EVERY_ACCESS
+	    printk( "%d IN, ", data_count );
+#endif
+	    if (data_count == 1) {
+	       *current_SC->SCp.ptr++ = inb( Read_FIFO_port );
+	       --current_SC->SCp.this_residual;
+	    } else {
+	       data_count >>= 1; /* Number of words */
+	       insw( Read_FIFO_port, current_SC->SCp.ptr, data_count );
+	       current_SC->SCp.ptr += 2 * data_count;
+	       current_SC->SCp.this_residual -= 2 * data_count;
+	    }
+	 }
+	 if (!current_SC->SCp.this_residual
+	     && current_SC->SCp.buffers_residual) {
+	    --current_SC->SCp.buffers_residual;
+	    ++current_SC->SCp.buffer;
+	    current_SC->SCp.ptr = current_SC->SCp.buffer->address;
+	    current_SC->SCp.this_residual = current_SC->SCp.buffer->length;
+	 }
+      }
+   }
+   
+   if (done) {
+#if EVERY_ACCESS
+      printk( " ** IN DONE %d ** ", current_SC->SCp.have_data_in );
+#endif
+
+#if ERRORS_ONLY
+      if (current_SC->cmnd[0] == REQUEST_SENSE && !current_SC->SCp.Status) {
+	 if ((unsigned char)(*((char *)current_SC->request_buffer+2)) & 0x0f) {
+	    unsigned char key;
+	    unsigned char code;
+	    unsigned char qualifier;
+
+	    key = (unsigned char)(*((char *)current_SC->request_buffer + 2))
+		  & 0x0f;
+	    code = (unsigned char)(*((char *)current_SC->request_buffer + 12));
+	    qualifier = (unsigned char)(*((char *)current_SC->request_buffer
+					  + 13));
+
+	    if (key != UNIT_ATTENTION
+		&& !(key == NOT_READY
+		     && code == 0x04
+		     && (!qualifier || qualifier == 0x02 || qualifier == 0x01))
+		&& !(key == ILLEGAL_REQUEST && (code == 0x25
+						|| code == 0x24
+						|| !code)))
+		  
+		  printk( "fdomain: REQUEST SENSE "
+			  "Key = %x, Code = %x, Qualifier = %x\n",
+			  key, code, qualifier );
+	 }
+      }
+#endif
+#if EVERY_ACCESS
+      printk( "BEFORE MY_DONE. . ." );
+#endif
+      my_done( (current_SC->SCp.Status & 0xff)
+	       | ((current_SC->SCp.Message & 0xff) << 8) | (DID_OK << 16) );
+#if EVERY_ACCESS
+      printk( "RETURNING.\n" );
+#endif
+      
+   } else {
+      if (current_SC->SCp.phase & disconnect) {
+	 outb( 0xd0 | FIFO_COUNT, Interrupt_Cntl_port );
+	 outb( 0x00, SCSI_Cntl_port );
+      } else {
+	 outb( 0x90 | FIFO_COUNT, Interrupt_Cntl_port );
+      }
+   }
+#if DEBUG_RACE
+   in_interrupt_flag = 0;
+#endif
+   return;
+}
+
+int fdomain_16x0_queue( Scsi_Cmnd * SCpnt, void (*done)(Scsi_Cmnd *))
+{
+   if (in_command) {
+      panic( "fdomain: fdomain_16x0_queue() NOT REENTRANT!\n" );
+   }
+#if EVERY_ACCESS
+   printk( "queue: target = %d cmnd = 0x%02x pieces = %d size = %u\n",
+	   SCpnt->target,
+	   *(unsigned char *)SCpnt->cmnd,
+	   SCpnt->use_sg,
+	   SCpnt->request_bufflen );
+#endif
+
+   fdomain_make_bus_idle();
+
+   current_SC            = SCpnt; /* Save this for the done function */
+   current_SC->scsi_done = done;
+
+   /* Initialize static data */
+
+   if (current_SC->use_sg) {
+      current_SC->SCp.buffer =
+	    (struct scatterlist *)current_SC->request_buffer;
+      current_SC->SCp.ptr              = current_SC->SCp.buffer->address;
+      current_SC->SCp.this_residual    = current_SC->SCp.buffer->length;
+      current_SC->SCp.buffers_residual = current_SC->use_sg - 1;
+   } else {
+      current_SC->SCp.ptr              = (char *)current_SC->request_buffer;
+      current_SC->SCp.this_residual    = current_SC->request_bufflen;
+      current_SC->SCp.buffer           = NULL;
+      current_SC->SCp.buffers_residual = 0;
+   }
+	 
+   
+   current_SC->SCp.Status              = 0;
+   current_SC->SCp.Message             = 0;
+   current_SC->SCp.have_data_in        = 0;
+   current_SC->SCp.sent_command        = 0;
+   current_SC->SCp.phase               = in_arbitration;
+
+   /* Start arbitration */
+   outb( 0x00, Interrupt_Cntl_port );
+   outb( 0x00, SCSI_Cntl_port );              /* Disable data drivers */
+   outb( adapter_mask, SCSI_Data_NoACK_port ); /* Set our id bit */
+   ++in_command;
+   outb( 0x20, Interrupt_Cntl_port );
+   outb( 0x14 | PARITY_MASK, TMC_Cntl_port ); /* Start arbitration */
+
+   return 0;
+}
+
+/* The following code, which simulates the old-style command function, was
+   taken from Tommy Thorn's aha1542.c file.  This code is Copyright (C)
+   1992 Tommy Thorn. */
+
+static volatile int internal_done_flag    = 0;
+static volatile int internal_done_errcode = 0;
+
+static void internal_done( Scsi_Cmnd *SCpnt )
+{
+    internal_done_errcode = SCpnt->result;
+    ++internal_done_flag;
+}
+
+int fdomain_16x0_command( Scsi_Cmnd *SCpnt )
+{
+    fdomain_16x0_queue( SCpnt, internal_done );
+
+    while (!internal_done_flag)
+	  ;
+    internal_done_flag = 0;
+    return internal_done_errcode;
+}
+
+/* End of code derived from Tommy Thorn's work. */
+
+void print_info( Scsi_Cmnd *SCpnt )
+{
+   unsigned int imr;
+   unsigned int irr;
+   unsigned int isr;
+
+   if (!SCpnt || !SCpnt->host) {
+      printk( "fdomain: cannot provide detailed information\n" );
+   }
+   
+   printk( "%s\n", fdomain_16x0_info( SCpnt->host ) );
+   print_banner( SCpnt->host );
+   switch (SCpnt->SCp.phase) {
+   case in_arbitration: printk( "arbitration " ); break;
+   case in_selection:   printk( "selection " );   break;
+   case in_other:       printk( "other " );       break;
+   default:             printk( "unknown " );     break;
+   }
+
+   printk( "(%d), target = %d cmnd = 0x%02x pieces = %d size = %u\n",
+	   SCpnt->SCp.phase,
+	   SCpnt->target,
+	   *(unsigned char *)SCpnt->cmnd,
+	   SCpnt->use_sg,
+	   SCpnt->request_bufflen );
+   printk( "sent_command = %d, have_data_in = %d, timeout = %d\n",
+	   SCpnt->SCp.sent_command,
+	   SCpnt->SCp.have_data_in,
+	   SCpnt->timeout );
+#if DEBUG_RACE
+   printk( "in_interrupt_flag = %d\n", in_interrupt_flag );
+#endif
+
+   imr = (inb( 0x0a1 ) << 8) + inb( 0x21 );
+   outb( 0x0a, 0xa0 );
+   irr = inb( 0xa0 ) << 8;
+   outb( 0x0a, 0x20 );
+   irr += inb( 0x20 );
+   outb( 0x0b, 0xa0 );
+   isr = inb( 0xa0 ) << 8;
+   outb( 0x0b, 0x20 );
+   isr += inb( 0x20 );
+
+				/* Print out interesting information */
+   printk( "IMR = 0x%04x", imr );
+   if (imr & (1 << interrupt_level))
+	 printk( " (masked)" );
+   printk( ", IRR = 0x%04x, ISR = 0x%04x\n", irr, isr );
+
+   printk( "SCSI Status      = 0x%02x\n", inb( SCSI_Status_port ) );
+   printk( "TMC Status       = 0x%02x", inb( TMC_Status_port ) );
+   if (inb( TMC_Status_port & 1))
+	 printk( " (interrupt)" );
+   printk( "\n" );
+   printk( "Interrupt Status = 0x%02x", inb( Interrupt_Status_port ) );
+   if (inb( Interrupt_Status_port ) & 0x08)
+	 printk( " (enabled)" );
+   printk( "\n" );
+   if (chip == tmc18c50 || chip == tmc18c30) {
+      printk( "FIFO Status      = 0x%02x\n", inb( port_base + FIFO_Status ) );
+      printk( "Int. Condition   = 0x%02x\n",
+	      inb( port_base + Interrupt_Cond ) );
+   }
+   printk( "Configuration 1  = 0x%02x\n", inb( port_base + Configuration1 ) );
+   if (chip == tmc18c50 || chip == tmc18c30)
+	 printk( "Configuration 2  = 0x%02x\n",
+		 inb( port_base + Configuration2 ) );
+}
+
+int fdomain_16x0_abort( Scsi_Cmnd *SCpnt)
+{
+   unsigned long flags;
+#if EVERY_ACCESS || ERRORS_ONLY || DEBUG_ABORT
+   printk( "fdomain: abort " );
+#endif
+
+   save_flags( flags );
+   cli();
+   if (!in_command) {
+#if EVERY_ACCESS || ERRORS_ONLY
+      printk( " (not in command)\n" );
+#endif
+      restore_flags( flags );
+      return SCSI_ABORT_NOT_RUNNING;
+   } else printk( "\n" );
+
+#if DEBUG_ABORT
+   print_info( SCpnt );
+#endif
+
+   fdomain_make_bus_idle();
+
+   current_SC->SCp.phase |= aborted;
+
+   current_SC->result = DID_ABORT << 16;
+
+   restore_flags( flags );
+   
+   /* Aborts are not done well. . . */
+   my_done( DID_ABORT << 16 );
+
+   return SCSI_ABORT_SUCCESS;
+}
+
+int fdomain_16x0_reset( Scsi_Cmnd *SCpnt, unsigned int flags )
+{
+#if DEBUG_RESET
+   static int called_once = 0;
+#endif
+
+#if ERRORS_ONLY
+   if (SCpnt) printk( "fdomain: SCSI Bus Reset\n" );
+#endif
+
+#if DEBUG_RESET
+   if (called_once) print_info( current_SC );
+   called_once = 1;
+#endif
+   
+   outb( 1, SCSI_Cntl_port );
+   do_pause( 2 );
+   outb( 0, SCSI_Cntl_port );
+   do_pause( 115 );
+   outb( 0, SCSI_Mode_Cntl_port );
+   outb( PARITY_MASK, TMC_Cntl_port );
+
+   /* Unless this is the very first call (i.e., SCPnt == NULL), everything
+      is probably hosed at this point.  We will, however, try to keep
+      things going by informing the high-level code that we need help. */
+
+   return SCSI_RESET_WAKEUP;
+}
+
+#include "sd.h"
+#include <scsi/scsi_ioctl.h>
+
+int fdomain_16x0_biosparam( Scsi_Disk *disk, kdev_t dev, int *info_array )
+{
+   int              drive;
+   unsigned char    buf[512 + sizeof( int ) * 2];
+   int		    size      = disk->capacity;
+   int              *sizes    = (int *)buf;
+   unsigned char    *data     = (unsigned char *)(sizes + 2);
+   unsigned char    do_read[] = { READ_6, 0, 0, 0, 1, 0 };
+   int              retcode;
+   struct drive_info {
+      unsigned short cylinders;
+      unsigned char  heads;
+      unsigned char  sectors;
+   } *i;
+   
+   /* NOTES:
+      The RAM area starts at 0x1f00 from the bios_base address.
+
+      For BIOS Version 2.0:
+      
+      The drive parameter table seems to start at 0x1f30.
+      The first byte's purpose is not known.
+      Next is the cylinder, head, and sector information.
+      The last 4 bytes appear to be the drive's size in sectors.
+      The other bytes in the drive parameter table are unknown.
+      If anyone figures them out, please send me mail, and I will
+      update these notes.
+
+      Tape drives do not get placed in this table.
+
+      There is another table at 0x1fea:
+      If the byte is 0x01, then the SCSI ID is not in use.
+      If the byte is 0x18 or 0x48, then the SCSI ID is in use,
+      although tapes don't seem to be in this table.  I haven't
+      seen any other numbers (in a limited sample).
+
+      0x1f2d is a drive count (i.e., not including tapes)
+
+      The table at 0x1fcc are I/O ports addresses for the various
+      operations.  I calculate these by hand in this driver code.
+
+      
+      
+      For the ISA-200S version of BIOS Version 2.0:
+
+      The drive parameter table starts at 0x1f33.
+
+      WARNING: Assume that the table entry is 25 bytes long.  Someone needs
+      to check this for the Quantum ISA-200S card.
+
+      
+      
+      For BIOS Version 3.2:
+
+      The drive parameter table starts at 0x1f70.  Each entry is
+      0x0a bytes long.  Heads are one less than we need to report.
+    */
+
+   drive = MINOR(dev) / 16;
+
+   if (bios_major == 2) {
+      switch (Quantum) {
+      case 2:			/* ISA_200S */
+				/* The value of 25 has never been verified.
+				   It should probably be 15. */
+	 i = (struct drive_info *)( (char *)bios_base + 0x1f33 + drive * 25 );
+	 break;
+      case 3:			/* ISA_250MG */
+	 i = (struct drive_info *)( (char *)bios_base + 0x1f36 + drive * 15 );
+	 break;
+      case 4:			/* ISA_200S (another one) */
+	 i = (struct drive_info *)( (char *)bios_base + 0x1f34 + drive * 15 );
+	 break;
+      default:
+	 i = (struct drive_info *)( (char *)bios_base + 0x1f31 + drive * 25 );
+	 break;
+      }
+      info_array[0] = i->heads;
+      info_array[1] = i->sectors;
+      info_array[2] = i->cylinders;
+   } else if (bios_major == 3
+	      && bios_minor >= 0
+	      && bios_minor < 4) { /* 3.0 and 3.2 BIOS */
+      i = (struct drive_info *)( (char *)bios_base + 0x1f71 + drive * 10 );
+      info_array[0] = i->heads + 1;
+      info_array[1] = i->sectors;
+      info_array[2] = i->cylinders;
+   } else {			/* 3.4 BIOS (and up?) */
+      /* This algorithm was provided by Future Domain (much thanks!). */
+
+      sizes[0] = 0;		/* zero bytes out */
+      sizes[1] = 512;		/* one sector in */
+      memcpy( data, do_read, sizeof( do_read ) );
+      retcode = kernel_scsi_ioctl( disk->device,
+				   SCSI_IOCTL_SEND_COMMAND,
+				   (void *)buf );
+      if (!retcode				    /* SCSI command ok */
+	  && data[511] == 0xaa && data[510] == 0x55 /* Partition table valid */
+	  && data[0x1c2]) {			    /* Partition type */
+
+	 /* The partition table layout is as follows:
+
+	    Start: 0x1b3h
+	    Offset: 0 = partition status
+		    1 = starting head
+		    2 = starting sector and cylinder (word, encoded)
+		    4 = partition type
+		    5 = ending head
+		    6 = ending sector and cylinder (word, encoded)
+		    8 = starting absolute sector (double word)
+		    c = number of sectors (double word)
+	    Signature: 0x1fe = 0x55aa
+
+	    So, this algorithm assumes:
+	    1) the first partition table is in use,
+	    2) the data in the first entry is correct, and
+	    3) partitions never divide cylinders
+
+	    Note that (1) may be FALSE for NetBSD (and other BSD flavors),
+	    as well as for Linux.  Note also, that Linux doesn't pay any
+	    attention to the fields that are used by this algorithm -- it
+	    only uses the absolute sector data.  Recent versions of Linux's
+	    fdisk(1) will fill this data in correctly, and forthcoming
+	    versions will check for consistency.
+
+	    Checking for a non-zero partition type is not part of the
+	    Future Domain algorithm, but it seemed to be a reasonable thing
+	    to do, especially in the Linux and BSD worlds. */
+
+	 info_array[0] = data[0x1c3] + 1;	    /* heads */
+	 info_array[1] = data[0x1c4] & 0x3f;	    /* sectors */
+      } else {
+
+ 	 /* Note that this new method guarantees that there will always be
+	    less than 1024 cylinders on a platter.  This is good for drives
+	    up to approximately 7.85GB (where 1GB = 1024 * 1024 kB). */
+
+	 if ((unsigned int)size >= 0x7e0000U) {
+	    info_array[0] = 0xff; /* heads   = 255 */
+	    info_array[1] = 0x3f; /* sectors =  63 */
+	 } else if ((unsigned int)size >= 0x200000U) {
+	    info_array[0] = 0x80; /* heads   = 128 */
+	    info_array[1] = 0x3f; /* sectors =  63 */
+	 } else {
+	    info_array[0] = 0x40; /* heads   =  64 */
+	    info_array[1] = 0x20; /* sectors =  32 */
+	 }
+      }
+				/* For both methods, compute the cylinders */
+      info_array[2] = (unsigned int)size / (info_array[0] * info_array[1] );
+   }
+   
+   return 0;
+}
+
+#ifdef MODULE
+/* Eventually this will go into an include file, but this will be later */
+Scsi_Host_Template driver_template = FDOMAIN_16X0;
+
+#include "scsi_module.c"
+#endif