[[!meta copyright="Copyright © 2007, 2008, 2009 Free Software Foundation,
Inc."]]

[[!meta license="""[[!toggle id="license" text="GFDL 1.2+"]][[!toggleable
id="license" text="Permission is granted to copy, distribute and/or modify this
document under the terms of the GNU Free Documentation License, Version 1.2 or
any later version published by the Free Software Foundation; with no Invariant
Sections, no Front-Cover Texts, and no Back-Cover Texts.  A copy of the license
is included in the section entitled
[[GNU Free Documentation License|/fdl]]."]]"""]]

[[!toc]]

# Xen dom0, hypervisor

/!\ Now that GNU Mach handles PAE you can use a PAE-enabled hypervisor.

You can either get binaries at <http://youpibouh.thefreecat.org/hurd-xen/> or build them yourself.

- Copy `gnumach-xen-pae` and `hurd-modules` to your dom0 /boot. If you still have a non-PAE hypervisor, use `gnumach-xen-nonpae` instead.
- Copy `hurd` into `/etc/xen`, edit it for fixing access to your hurd / and swap

# GNU/Hurd system

/!\ You need an already installed [[GNU/Hurd_system|hurd/running]].

If you have a free partition, you can fdisk to type 0x83, create a filesystem using:

    sudo mke2fs -b 4096 -I 128 -o hurd /dev/sda4 

Replace /dev/sda4 with your partition. Install and use crosshurd to setup a GNU/Hurd system on this partition.

# /etc/xen/hurd configuration

Here is a sample /etc/xen/hurd configuration

    kernel = "/boot/gnumach-xen-pae"
    memory = 256
    disk = ['phy:sda4,hda,w']
    extra = "root=device:hd0"
    vif = [ '' ]
    ramdisk = "/boot/hurd-modules"

Do not give more than 580MB memory (due to bootstrap limitations, it's not easy
to map more).

Suggestions about [[networking_configuration]] are available.

If you need stable MAC addresses, use a syntax like `vif = [
'mac=00:16:3e:XX:XX:XX, bridge=br0' ]`.

# Running Hurd with Xen

To run Hurd with Xen, use:

    xm create -c hurd

and gnumach should get started. Proceed with native-install.

    export TERM=mach
    ./native-install

- If `xm` complains about networking (`vif could not be connected`), it's Xen scripts' fault, see Xen documentation for how to configure the network.  The simplest way is network-bridge with fixed IPs (note that you need the bridge-utils package for this).  You can also just disable networking by commenting the vif line in the config.
- If `xm` complains `Error: (2, 'Invalid kernel', 'xc_dom_compat_check: guest type xen-3.0-x86_32 not supported by xen kernel, sorry\n')`, you most probably have a PAE-enabled hypervisor and a non-PAE gnumach. Either install and boot non-PAE hypervisor and kernel, or rebuilt gnumach in PAE mode.

# Building from sources

If you want to generate these images, first get the `gnumach-1-branch-Xen-branch` branch from gnumach CVS.
Then look for "Ugly" in `kern/bootstrap.c`, how to generate `hurd-modules` is explained there, and you'll have to fix `EXT2FS_SIZE` and `LD_SO_SIZE` by hand.
Then use

    ./configure --enable-platform=xen
    make

The current `hurd-modules` was built from the debian packages `hurd 20070606-2` and `libc0.3 2.6.1-1`.
/!\ This means that when using this image, your GNU/Hurd system also needs to be a glibc version 2.6 or later-based one!

---

# Miscellaneous

[[Internals]].

[[!GNU_Savannah_task 5468]], [[!GNU_Savannah_task 6584]].

---

# `pv-grub`

From Xen 4.0 on you'll be able to run the GNU Hurd directly using `pv-grub`,
without the need to [prepare a special bootstrap
image](http://youpibouh.thefreecat.org/hurd-xen/build_hurd-modules) (like an
initrd).